Dell Force10 Z9000 Research

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 34
service-class dynamic dot1p...1187 show interfaces rate...1188 strict-priority queue...1191 Policy-Based QoS Commands...1191 bandwidth-percentage...1192 bandwidth-weight...1192 class-map...1193 clear qos statistics...1194 description...1195 match ip access-group...1196 match ip dscp...1197 match ip precedence...1198 match mac access... backplane ignore-backpressure...1206 queue egress...1206 queue ingress...1207 rate-limit...1208 rate-police...1209 rate-shape...1210 service-policy input...1211 service-policy output...1212 service-queue...1213 set.........1227 test cam-usage...1228 threshold...1230

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 110
... is the default setting and is supported on FTOS versions 8.2.1.0 and earlier. 110 Values changed as described above. The 10.4 setting is available on the E-Series ExaScale E600i. Introduced on the E300, E600/E600i, and E1200. 10.4 CONFIGURATION Version 8.3.1.0 Version 8.1.1.2 Version 8.1.1.0 Version 6.2.1.1 Version 6.1.1.0 Added the 2.4 micro-seconds option. When using nine SFMs in an ExaScale chassis reduces throughput at any epoch setting. Parameters Defaults Command Modes Command History Usage...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 151
... boot. n/a PP1 - Displays the number of ports in the slot. Displays the temperature of the line card processor. Lists the type of hours and minutes the card is online. Displays an internal code, which version was used in the chassis: • AC = AC power supply • DC = DC Power Entry Module (PEM) Voltage Serial Number Part Num Vendor ID Date Code Displays OK if the line voltage is within range. Displays the line card type configured for the slot. Displays the operating software version. Minor alarm status if the temperature...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 177
... S50-01-24G-2S 1 -- Power Supplies -- Unit 0 -Unit Type Status Next Boot Required Type Current Type Master priority : Management Unit : online : online : Z9000 - 32-port TE/FG (ZB) : Z9000 - 32-port TE/FG (ZB) : 0 177 The Boot Flash field displays the code level for boot code 2.8.1.1 and newer, while older boot codes display as "Present". FTOS#show system stack-unit command output to support Piece Part ID (PPID). Unit UnitType Status ReqTyp CurTyp Version Ports ---------- -- 0 Member not present...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 178
... 02 : 11 : 01192010 : 01 : soft reset : disabled : 00:01:e8:81:e1:b9 : 3 -- Unit 0 -Unit Type Status Next Boot Required Type Current Type Master priority Hardware Rev Num Ports Up Time FTOS Version Jumbo Capable POE Capable Boot Flash Memory Size Temperature Voltage Serial Number Part Number Vendor Id Date Code Country Code Last Restart Auto Reboot Burned In MAC No Of MACs : Management Unit : online : online : S4810 - 48-port E/FE/GE (SC) : S4810 - 48...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 734
..." data packet using the Fast Ethernet MLT-3 waveform. The IEEE Ethernet standard does not support setting a speed to exactly match the mode of flow control supported by the remote interface AutoNegotiation Expansion ParallelDetectionFault is either half or full. show interfaces gigabitethernet command Example below. E-Series line cards support both full-duplex and half-duplex 1000BaseT. Mode Control Indicates if auto negotiation is the types of operation as the link partner...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 1294
... Information Related Commands Version 8.3.11.1 Version 8.3.7.0 Version 7.6.1.0 Version 7.5.1.0 Version 6.2.1.0 Introduced on the terminal lines. If you configure aaa authentication enable default, FTOS uses the methods defined for the enable command. The TACACS+ is incorrect, but the server key is the default method for user access to the next authentication method. enables AAA login authentication on the Z9000. creates a password. Parameters method-list-name default method Enter a text string (up to 16 characters...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 1305
... by a number from 25 to 63 characters. Parameters Defaults Command Modes Command History Usage Information name access-class access-list-name nopassword password secret encryption-type Enter a text string for the password option is 0. Enter the keyword password followed by the name of the user up to specify that you will follow . The default encryption type for the name of a configured access control list (either a IP access control list or MAC access control list). Enter...

FTOS Configuration Guide for Z9000 System

Page 99
... error message is shown if IPv6 microcode is configured and an ACL is entered with IPv6 microcode. icmp | ip | tcp | udp} {source mask | any | host ip-address} {destination mask | any | host ip-address} [operator port [port]] [count [byte] | log] [order] [monitor] [fragments] When you use these packets' details. To delete a filter, enter the show config command in the IP ACCESS LIST mode and locate the sequence number of...

FTOS Configuration Guide for Z9000 System

Page 244
... and Normal mode. • BMP mode (default): The switch automatically configures all ports (management and user ports) as Layer 3 physical ports and acts as a DHCP client on the server: host S4810 { hardware ethernet 00:01:e8:81:e2:39; www.dell.com | support.dell.com BMP mode is set with the reload-type normal-reload command. This mode obtains the FTOS image and configuration file from Dell Force10. Use Normal mode to boot the switch up configuration file...

FTOS Configuration Guide for Z9000 System

Page 408
..., check their documentation when planing MTU sizes across a network. In FTOS, MTU is used for a period of the following show interfaces interface x/y Configure MTU size on platforms: Ethernet Pause Frames allow for each transmission media. A situation may arise where a sending device may transmit data faster than the size set in the ip mtu command. Table 19-6. Clearing Dampening Counters FTOS# clear dampening interface Gi...

FTOS Configuration Guide for Z9000 System

Page 409
The following error message appears when trying to define the controls more closely. Interfaces | 409 To allow full duplex flow control, stations implementing the pause operation instruct the MAC to this multicast address. The only configuration applicable to enable flow control when half duplex is already configured: Can't configure flowcontrol when half duplex is configure, config ignored. Threshold Settings c s z Threshold Settings are supported on the interface. The pause ends when...

FTOS Configuration Guide for Z9000 System

Page 491
... time manually. This timer can be set in the supported TLVs. The duration can track IS-IS information on adjacency settings with the value derived from the helping router. By default, FTOS supports dynamic hostname exchange to an IS-IS NET address, you can be configured as a Level 1 router, a Level 2 router, or a Level 1-2 router. To support IPv6, the Dell Force10 implementation...

FTOS Configuration Guide for Z9000 System

Page 537
... intervals, the state changes to the remote end of the link. 3. Enable FEFD Globally To enable FEFD globally on all interfaces from CONFIGURATION mode, or on a per interface basis; Configuring FEFD You can become operational again. Layer 2 | 537 1. An interface on physical Ethernet interfaces only, excluding the management interface. Table 24-1. All interfaces in the Err-disabled state must be manually reset using the fefd reset [interface] command in EXEC privilege mode (it transitions...

FTOS Configuration Guide for Z9000 System

Page 784
... accounted functions. User-defined method lists take precedence over the default method list. To obtain accounting records displaying information about users currently logged in which they are applied. www.dell.com | support.dell.com No specific show command exists for terminal lines • Configure AAA Authentication login methods • Enable AAA Authentication • AAA Authentication-RADIUS For a complete listing of all user authentication and network service access information. Figure...

FTOS Configuration Guide for Z9000 System

Page 800
... server key is still authenticated by the secondary method. 800 | Security Use this command multiple times to configure multiple TACACS+ server hosts. 2 aaa authentication login {method-list-name | default} tacacs+ [...method3] CONFIGURATION Enter a text string (up to use the show config in the LINE mode or the show running-config tacacs+ command in the CONFIGURATION mode: Step Command Syntax Command Mode Purpose 1 tacacs-server host {ip-address | host} CONFIGURATION Configure a TACACS+ server host. www.dell.com | support.dell...

FTOS Configuration Guide for Z9000 System

Page 806
... (SSH) is disabled by prompting for a password when attempting to connect to the Dell Force10 system. Enable SSH password authentication using version 1 or version 2, respectively. Enable it using the command show ip ssh rsa-authentication: Display the authorized-keys for the RSA authentication. • ssh-peer-rpm: Open an SSH connection to the peer RPM. www.dell.com | support.dell.com • ip ssh connection-rate-limit: Configure the maximum number of incoming...

FTOS Configuration Guide for Z9000 System

Page 919
...; Dell Force10 strongly recommends configuring a static LAG for devices attached on non-VLT ports. • Port-channel link aggregation (LAG) across the two chassis. If the system detects mismatches between the VLT peer nodes. • VLT peer switches operate as separate chassis with independent control and data planes for the VLTi being down, use the show vlt statistics command to verify there are mismatch errors, then use the...

FTOS Configuration Guide for Z9000 System

Page 928
Connect the peer switches in default mode (no ip address INTERFACE PORT-CHANNEL 3 Add one of -band management network. no switchport or VLAN assigned). 2 Remove an IP address from the interface. Enter the slot (0-1) and the port (0). CONFIGURATION Note: To be included in the VLTi, the port channel must be used for the backup link through an out-of the following interface types: PORT-CHANNEL 1-Gigabit Ethernet: Enter gigabitethernet slot/port. 10-Gigabit Ethernet: Enter...

FTOS Configuration Guide for Z9000 System

Page 945
..., T - GVRP tagged, M - interface Port-channel 11 On an access device, verify the no ip address switchport channel-member fortyGigE 1/18,22 port-channel connection to an attached device FTOS_VLTpeer2(conf-if-po-110)#channel-member fortyGigE 0/48 FTOS_VLTpeer2(conf-if-po-110)#no shutdown Virtual Link Trunking (VLT) | 945 Internal tagged, v - GVRP VLANs, R - Dot1x untagged, X - VLT untagged, V - Remote Port Mirroring VLANs, P - Default VLAN, G - Primary...

Dell Force10 Z9000 Research

Related Manual Pages

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

FTOS Configuration Guide for Z9000 System

Related Videos

Similar Questions

Related Terms

Ask a New Question

Manuals / Documents

Related Items

Points & Prizes

Dell Manuals

Dell Reviews

Contact Information

Scoreboard Ratings

Dell Recalls