Cisco 2980G - Catalyst Switch Support and Manuals
Cisco 2980G Videos
Popular Cisco 2980G Manual Pages
Hardware Installation Guide - Page 19
... continue. • P4-You need technical assistance with Cisco. Registered users can order products, check on Cisco product capabilities,
product installation, or basic product configuration.
Preface
Obtaining Technical Assistance
services, and programs. In addition, you have a priority level 3 (P3) or priority level 4 (P4) problem, contact TAC by a maintenance contract. To register for...
Hardware Installation Guide - Page 26
...
Note A Category 5 cable is a straight-through, twisted-pair cable.
Refer to the Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide for more info on the Catalyst 2900 XL switches provide protocol support for autonegotiation, the port senses the speed and duplex settings of half duplex, full duplex, 10 Mbps, or 100 Mbps. For more information...
Software Guide - Page 29
... Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
xxix
When you have complete access to the technical support resources on the Cisco TAC website. To access the Cisco TAC website, go to this URL: http://www.cisco.com/tac
All customers, partners, and resellers who need information or assistance concerning Cisco product capabilities,
product installation...
Software Guide - Page 33
...the module. Table 1-3 Catalyst 2980G Switch
Product Number WS-C2980G-A
Chassis Description Catalyst 2980G • Fixed-configuration switch • 12-Gbps backplane • Optional redundant power supplies • Two 1000BASE-X (GBIC) Gigabit Ethernet ports • 80 10/100BASE-TX Fast Ethernet ports
Supervisor Engine Software
The supervisor engine software is factory installed on every...
Software Guide - Page 177
... chapter, refer to the Catalyst 4500 Series, Catalyst 2948G, and Catalyst 2980G Switches Command Reference. Configuring VTP
CH A P T E R
9
This chapter describes how to configure the VLAN Trunking Protocol (VTP) on configuring VLANs, see Chapter 10, "Configuring VLANs."
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1 9-1
Software Guide - Page 203
... | secret} show config
This example shows how to set a VTP password and verify the configuration:
Console> (enable) set vtp passwd toto secret VTP secret has to be shown in length Console> (enable)
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
9-27 set VTP passwords, perform this task in privileged mode:
Step 1 Step...
Software Guide - Page 222
... is a VLAN that port. Broadcasts propagate only between associated community ports and the promiscuous port.
10-16
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01 Table 10-3 lists the set of supporting VLANs that the phone send untagged packets. Command
show port auxiliaryvlan {vlan | untagged | dot1p | none}
This...
Software Guide - Page 260
... 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01
Console> show vmps server
VMPS Client Status:
VMPS VQP Version:
1
Reconfirm Interval: 60 min
Server Retry Count: 3
VMPS domain server: 192.0.0.1 (primary)
192.0.0.6
192.0.0.9
This example shows how to set port membership 2/1 dynamic
Spantree port fast start option enabled...
Software Guide - Page 298
... Received:500 Join Empties:200 Join INs:250
15-14
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01 The more registered attributes there are set differently on all Layer 2-connected devices. Console> (enable) set garp timer leave 650
GMRP/GARP leave timer value is set to display GMRP statistics for VLAN 23:
Console> show...
Software Guide - Page 300
...multicast groups manually and verify the configuration (the asterisks indicate that the entry was manually configured):
Console> (enable) set cam static 01-33-44-55-66-77 2/6-12 Static multicast entry added to CAM table. Console> (enable) show multicast group CGMP enabled IGMP disabled
15-16
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release...
Software Guide - Page 378
Command set snmp access-list 2 172.20.60.7 mask 255.255.255.0 Access number 2 has been updated with existing IP Address 172.20.60.7 mask 255.255.255.0 Console> (enable)
This example shows how to display the SNMP configuration:
Console> (enable) show snmp ifalias [ifIndex]
24-10
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-...
Software Guide - Page 423
... 28-1 on page 28-4 for each power supply.
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
28-3
Variable power supplies automatically adjust the power resources to accommodate the chassis and inline power requirements. • When your switch is set to combined mode, the total available power is P + (P * ratio). • See...
Software Guide - Page 457
...You must reset the password after installing software release 5.4 or a later release to 30 characters, and use any printable ASCII characters, including a space.
Passwords are set the enable password for access. Enter your new password.
Console> (enable)
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
30...
Software Guide - Page 459
...least one alphabetic character. picard
15
Console> (enable)
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
30-15 The login password is null for 30 seconds when you are connected to reboot the switch.
You cannot recover the password if you are connected through the supervisor engine console port. Enter privileged...
Software Guide - Page 480
...Disable the credentials forwarding configuration. clear kerberos credentials forward
30-36
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01 To configure clients to forward user credentials as they connect to other network services:
Console> (enable) set kerberos clients mandatory Kerberos clients set to None Kerberos config...
Cisco 2980G Reviews
Do you have an experience with the Cisco 2980G that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!