Activating the Integrated RAID Controller
Page 3
Dell™ Systems Activating the Integrated RAID Controller www.dell.com | support.dell.com
Dell™ Systems Activating the Integrated RAID Controller www.dell.com | support.dell.com
Activating the Integrated RAID Controller
Page 5
...). 2 Turn off the system, including any of the riser card. If you have a PowerEdge 2800 system, go to activate the integrated RAID controller on Dell™ PowerEdge™ 1850, 2800, and 2850 systems. Your upgrade kit includes a RAID controller memory module, RAID hardware key, RAID battery, and RAID software. NOTICE: To avoid possible data loss, back up all data on the...
...). 2 Turn off the system, including any of the riser card. If you have a PowerEdge 2800 system, go to activate the integrated RAID controller on Dell™ PowerEdge™ 1850, 2800, and 2850 systems. Your upgrade kit includes a RAID controller memory module, RAID hardware key, RAID battery, and RAID software. NOTICE: To avoid possible data loss, back up all data on the...
Activating the Integrated RAID Controller
Page 6
Figure 1-2. See Figure 1-2. www.dell.com | support.dell.com Figure 1-1. Installing the RAID Controller Memory Module ejectors (2) alignment key 7 Locate the memory module that is included with the upgrade kit. 8 Align the RAID memory module's edge connector with the alignment key, and insert the memory module into the connector. NOTE: Do not substitute unbuffered DDR 2 memory...
Figure 1-2. See Figure 1-2. www.dell.com | support.dell.com Figure 1-1. Installing the RAID Controller Memory Module ejectors (2) alignment key 7 Locate the memory module that is included with the upgrade kit. 8 Align the RAID memory module's edge connector with the alignment key, and insert the memory module into the connector. NOTE: Do not substitute unbuffered DDR 2 memory...
Activating the Integrated RAID Controller
Page 7
...the inside of the system cover for the location of the RAID key connector. 11 If you have a PowerEdge 1850 system, go to step 13. 12 If you have a PowerEdge 2850 system: a Position the RAID battery over the RAID battery holder with your index fingers to lock the memory ...system. If you are replacing a RAID battery, see the "Battery Disposal" section in the riser, which is adjacent to the RAID battery cable connector on the riser. b Route the battery cable through the notch in your Product Information Guide for more information. Activating the Integrated RAID Controller 1-5
...the inside of the system cover for the location of the RAID key connector. 11 If you have a PowerEdge 1850 system, go to step 13. 12 If you have a PowerEdge 2850 system: a Position the RAID battery over the RAID battery holder with your index fingers to lock the memory ...system. If you are replacing a RAID battery, see the "Battery Disposal" section in the riser, which is adjacent to the RAID battery cable connector on the riser. b Route the battery cable through the notch in your Product Information Guide for more information. Activating the Integrated RAID Controller 1-5
Activating the Integrated RAID Controller
Page 8
... before you have a PowerEdge 2800 system, go to 4 hours of the RAID hardware. 21 Install and configure the RAID software. See your RAID documentation for 3 to step 18. NOTICE: The newly-installed RAID battery must be charged for more information. Installing the RAID Key hardware key latches (2) 17 If you can operate the RAID controller in write-back...
... before you have a PowerEdge 2800 system, go to 4 hours of the RAID hardware. 21 Install and configure the RAID software. See your RAID documentation for 3 to step 18. NOTICE: The newly-installed RAID battery must be charged for more information. Installing the RAID Key hardware key latches (2) 17 If you can operate the RAID controller in write-back...