Activating the Integrated RAID Controller
Page 5
...each end of the insulator, then lift the insulator off the system, including any of riser card that your system. If you have a PowerEdge 2850, remove the riser card. 5 Locate the RAID memory module connector on the riser card, you perform the following procedures, ensure that is ...not present on the riser card. Before you have a PowerEdge 2800 system, go to step 5. NOTICE: To avoid possible data loss, back up all data on Dell™ PowerEdge™ 1850, 2800, and 2850 systems. Your upgrade kit includes a RAID controller memory module, RAID hardware key,...
...each end of the insulator, then lift the insulator off the system, including any of riser card that your system. If you have a PowerEdge 2850, remove the riser card. 5 Locate the RAID memory module connector on the riser card, you perform the following procedures, ensure that is ...not present on the riser card. Before you have a PowerEdge 2800 system, go to step 5. NOTICE: To avoid possible data loss, back up all data on Dell™ PowerEdge™ 1850, 2800, and 2850 systems. Your upgrade kit includes a RAID controller memory module, RAID hardware key,...
Activating the Integrated RAID Controller
Page 8
...hours of the RAID hardware. 21 Install and configure the RAID software. If you have a PowerEdge 2850 system, replace the riser card. 18 Close the system. 19 Reconnect the system to its electrical...for the SCSI controller has changed to reflect the presence of system operation before you have a PowerEdge 1850 system, place the plastic riser card insulator over the riser card and press down on ...bezel (if applicable). 1-6 Activating the Integrated RAID Controller www.dell.com | support.dell.com Figure 1-3. NOTICE: The newly-installed RAID battery must be charged for more information.
...hours of the RAID hardware. 21 Install and configure the RAID software. If you have a PowerEdge 2850 system, replace the riser card. 18 Close the system. 19 Reconnect the system to its electrical...for the SCSI controller has changed to reflect the presence of system operation before you have a PowerEdge 1850 system, place the plastic riser card insulator over the riser card and press down on ...bezel (if applicable). 1-6 Activating the Integrated RAID Controller www.dell.com | support.dell.com Figure 1-3. NOTICE: The newly-installed RAID battery must be charged for more information.
Updating Your NIC Teaming Drivers (.pdf)
Page 7
... tray. 12 If applicable, remove the RAC card. Upgrading Your System Board and Riser Board 7 Removing and Replacing the System Board and Riser Board In A Dell PowerEdge 2850 System Removing the System Board 1 If applicable, remove the bezel. 2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet...
... tray. 12 If applicable, remove the RAC card. Upgrading Your System Board and Riser Board 7 Removing and Replacing the System Board and Riser Board In A Dell PowerEdge 2850 System Removing the System Board 1 If applicable, remove the bezel. 2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet...
Updating Your NIC Teaming Drivers (.pdf)
Page 9
... cover. 18 If applicable, reattach the bezel. See Figure 1-4. b Slide the front-fan tray to the riser board. See "Upgrading the Dell PowerEdge 2850 Expansion-Card Riser Board." 15 Reinstall the expansion-card-cage. Installing the New System Board and Riser Board 1 Unpack the new system board. 2 ... the retention pin engages. 4 Replace the front-fan tray: a Place the front-fan tray over the three securing posts. Upgrading the Dell PowerEdge 2850 Expansion-Card Riser Board 1 If applicable, remove the RAID memory module from the expansion-card riser board. 2 Press both release tabs on...
... cover. 18 If applicable, reattach the bezel. See Figure 1-4. b Slide the front-fan tray to the riser board. See "Upgrading the Dell PowerEdge 2850 Expansion-Card Riser Board." 15 Reinstall the expansion-card-cage. Installing the New System Board and Riser Board 1 Unpack the new system board. 2 ... the retention pin engages. 4 Replace the front-fan tray: a Place the front-fan tray over the three securing posts. Upgrading the Dell PowerEdge 2850 Expansion-Card Riser Board 1 If applicable, remove the RAID memory module from the expansion-card riser board. 2 Press both release tabs on...
Updating Your NIC Teaming Drivers (.pdf)
Page 10
Removing the Expansion-Card Riser Board From a Dell PowerEdge 2850 System slots tabs RAID memory module connector expansion-card riser board retention pin RAID battery connector expansion-card guide expansion card openings expansion-card guide .... 6 Close the expansion-card guide. 7 If applicable, reinstall the RAID memory module onto the riser board. 10 Upgrading Your System Board and Riser Board www.dell.com | support.dell.com Figure 1-4.
Removing the Expansion-Card Riser Board From a Dell PowerEdge 2850 System slots tabs RAID memory module connector expansion-card riser board retention pin RAID battery connector expansion-card guide expansion card openings expansion-card guide .... 6 Close the expansion-card guide. 7 If applicable, reinstall the RAID memory module onto the riser board. 10 Upgrading Your System Board and Riser Board www.dell.com | support.dell.com Figure 1-4.