Zenith SL-6053-WH - Heath - Wireless Command Support and Manuals
Get Help and Manuals for this Zenith item
View All Support Options Below
Free Zenith SL-6053-WH manuals!
Problems with Zenith SL-6053-WH?
Ask a Question
Free Zenith SL-6053-WH manuals!
Problems with Zenith SL-6053-WH?
Ask a Question
Most Recent Zenith SL-6053-WH Questions
Has The Sl-6053 Been Discontinued Or Is It Just Out Of Stock?
(Posted by jclout4153 9 years ago)
Three Flash Error Code.
I have two 240 degree sensors. One works fine, the other gives me three flashes on the LED light con...
I have two 240 degree sensors. One works fine, the other gives me three flashes on the LED light con...
(Posted by dowellpj 10 years ago)
Help With Dual Brite Lites
Good morning. I have 6 dual brite lights (black lantern style) around my newly remodeled home. I hav...
Good morning. I have 6 dual brite lights (black lantern style) around my newly remodeled home. I hav...
(Posted by kestridge 12 years ago)
Reciever Not Working
Sensor is seeing object but not communicating with reciever IF it works, it doesn't turn the light ...
Sensor is seeing object but not communicating with reciever IF it works, it doesn't turn the light ...
(Posted by nextstage1 14 years ago)
Popular Zenith SL-6053-WH Manual Pages
User Guide - Page 1
Floodlight
This manual includes operating instructions for switch locations.
( - Features
• Products are 8 codes available by changing the settings of switches 1 through 3 set the code setting to match.
Heath®/Zenith wireless lighting controls are designed to a different code. Code Settings, System 2 Note: When operating more than one system independently of remote ...
User Guide - Page 2
...1 2 3 4
Close-Up of Typical Code Switch (Factory Default Setting is Off)
598-1306-04 Code Switch Locations
Code Switches
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
180° Motion Sensor
Code Switches
CODES
DETECT
1 2 3 4
DAY NIGHT NIGHT ONLY
240° Motion Sensor
CR2032 3 VOLTS
ON 1 2 34
Code Switches Entry Switch
Code Switches
LAMP MODE switches
RAINTIGHT
ã THIS END UP...
User Guide - Page 3
...
Replace battery compartment cover by sliding the cover down in order to 100 feet (30 m) away.
Select Night or 24 Hour Mode These motion sensors are able to either the DAY/NIGHT or NIGHT ONLY position. To set the detection mode, remove battery compartment cover by reversing the above instructions. Slide the DETECT switch to...
User Guide - Page 4
... B. Adjust RANGE Control. Set the DETECT control switch to change temperature rapidly, such as heating vents, fans, and air conditioners. Slide the ON-TIME control to TEST mode. Set the ON-TIME control to the corresponding setting. Walk in the day time: A. Set ON-TIME Control.
Do not point other lights at motion sensor.
Locate the RANGE...
User Guide - Page 5
... m) Maximum Range
Maximum Coverage Angle
240° Motion Sensor Coverage Area
Aim Sensor Down for Short Coverage
Aim Sensor Higher for Long Coverage
Adjusting Motion Sensor Coverage
598-1306-04
ENGLISH
8 ft. (2.4 m)
180°
Motion
Motion
70 ft. (21 m) Maximum Range
Maximum Coverage Angle
180° Motion Sensor Coverage Area
Sensor
Sensor
Least Sensitive
Most...
User Guide - Page 6
... entry otfrMaonvesmemnt itter. of battery chamber.
3. Install replacement battery Screwdriver
in alignment
(see illustration). Press...light on door or window (moving surface).
Snap transmitter onto
CR2032 Lithium Battery
(maximum distance may vary depending on when entering a closet, attic, room, etc. 1. Entry Switch
Installation... of
(see Troubleshooting Guide.
4. Battery ...
User Guide - Page 7
...connections to make sure they must be replaced by a qualified electrician. Use the two wall switch screws (long) supplied to mount the ...ing codes may need to bend the wires to fit inside the box. Use one of insulation from the old switch. Route.... WARNING: Turn off the power to the light switch circuit
before you do not install to the right. ENGLISH
Receiver Information
All receivers...
User Guide - Page 8
... button to decrease brightness.
The light should turn on . 3. Push and release top of DIM button to increase brightness. Bulb Replacement Move the power disconnect switch to 50% in the ON (right side)
position. 2. Verify the power disconnect switch is switched on
full bright. Note: If you are 5 DIM settings ranging from ON or OFF, push...
User Guide - Page 9
...wiring required. • Install fixture in accordance with local codes. Do not aim the ...light fixture. 2. Insert the small end into module. Secure with mounting bolt. 7. Caulk the wall plate mounting surface with receiver (see transmitter instructions...-on effects) available when motion is no longer detected and... modes (light turn the receiver ON or OFF. Set the LAMP MODE switch to hold...
User Guide - Page 10
.... If the problem persists, call 1-800-858-8501 (English speaking only) for 90 second initialization period
(remote motion sensor). 5. Verify circuit breaker or fuse is cautioned that changes or modifications not expressly approved by another device.
4. No Service Parts Available for assistance at : www.hzsupport.com. Technical Service Please call * for this guide. Device comes...
User Guide - Page 11
... from state to state or province to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by factory defective parts or workmanship will void this warranty. This warranty does not include reimbursement for all warranty requests. Repair service, adjustment and calibration due to province. THIS WARRANTY IS EXPRESSLY IN...
Zenith SL-6053-WH Reviews
We have not received any reviews for Zenith yet.