Zenith SL-6030-WH5 - Heath - Wireless Command Motion Sensor Support and Manuals
Get Help and Manuals for this Zenith item
View All Support Options Below
Free Zenith SL-6030-WH5 manuals!
Problems with Zenith SL-6030-WH5?
Ask a Question
Free Zenith SL-6030-WH5 manuals!
Problems with Zenith SL-6030-WH5?
Ask a Question
Most Recent Zenith SL-6030-WH5 Questions
Sl 6030 Tx Motion Sensor-floodlight
my light does not turn off. The transmitter seems to be functioning..If receiver us faulty, do i nee...
my light does not turn off. The transmitter seems to be functioning..If receiver us faulty, do i nee...
(Posted by Jfalk1 5 years ago)
Replacement For Sl-6030-tx
What is the replacement for the zenith SL-6030-TX motion sensor
What is the replacement for the zenith SL-6030-TX motion sensor
(Posted by F58lrpl75ranger 7 years ago)
What If We Put New Batteries In And It Is Still Not Working
what if I put new batteries in and it's still doesn't work
what if I put new batteries in and it's still doesn't work
(Posted by bustos1155 8 years ago)
Interchangable Sensors
My old unit sensor seems to be in a state of malfunction. If I purchase a new SL 6030 TX, will the n...
My old unit sensor seems to be in a state of malfunction. If I purchase a new SL 6030 TX, will the n...
(Posted by sanks2u 11 years ago)
Popular Zenith SL-6030-WH5 Manual Pages
User Guide - Page 1
...off. Switches 1 through 3. This manual applies to match.
All products work together. Heath®/Zenith wireless lighting controls are 8 codes available by changing the settings of up to work on the same principle and use the same code setting information. Code Settings
Note: Most single system installations will not require any specific information pertaining to a different...
User Guide - Page 2
... AND CEILING MOUNT ONLY
SUITABLE FOR WET LOCATION MADE IN CHINA
Floodlight
Note: The "X" has been placed on the switches to help clarify the code settings on the previous page.
Code Switch Locations
Code Switches
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
180° Motion Sensor
Code Switches
CODES
DETECT
1 2 3 4
DAY NIGHT NIGHT ONLY
240° Motion Sensor
Code
Switches
ON
Wall...
User Guide - Page 3
...curved surface such as a post. 2. Installing Motion Sensor 1.
Note: Attach mounting bracket vertically if connecting to polarity markings inside the battery compartment.
Attach motion sensor mounting bracket to maintain water tightness. To set the detection mode, remove battery compartment cover by reversing the above instructions. Replace battery compartment cover by sliding...
User Guide - Page 4
... vents, fans, and air conditioners. Set ON-TIME Control.
DualBrite® Dimmer Control (240° Motion Sensor Only)
Light comes on the bottom
of the motion sensor. Do not point other lights at motion sensor. Check Operation. Loosen the clamp screw and move the motion sensor to check operation in the day time: A. Adjust RANGE Control. Determine the amount of...
User Guide - Page 5
... Range
Maximum Coverage Angle
240° Motion Sensor Coverage Area
Aim Sensor Down for Short Coverage
Aim Sensor Higher for Long Coverage
Adjusting Motion Sensor Coverage
598-1306-02
ENGLISH
8 ft. (2.4 m)
180°
Motion
Motion
70 ft. (21 m) Maximum Range
Maximum Coverage Angle
180° Motion Sensor Coverage Area
Sensor
Sensor
Least Sensitive
Most Sensitive
The detector...
User Guide - Page 6
...installed. See rating label on wait 15 seconds. Connect the second black power wire from the old switch. Mount wall plate on the power to make sure they must be replaced... may require installation by wall switch receiver.
2. Do this at your circuit breaker or fuse box.
3. ing codes may need...switch only). • Not for use with 120 volt incandescent or halogen bulbs.
Note: If...
User Guide - Page 7
... DIM button to increase brightness. Note: DIM setting remembers last setting used. The light should turn off. 4. Set desired DIM level. Note: The DIM setting defaults to the OFF (left side) position. CAUTION: Do not exceed the maximum load limits listed above.
598-1306-02
Bulb Replacement Move the power disconnect switch to 50% in...
User Guide - Page 8
... ground wire to green ground screw on .
• SOFT
- Light flashes on then off when motion is detected:
• NORMAL
or
- Install the mounting strap as shown. Secure with receiver (see transmitter instructions). Secure with silicone weather sealant.
9. Adjust the lamp holders by loosening the lock nuts. Note: Do not rotate the lamp holders more...
User Guide - Page 9
Troubleshooting Guide
POSSIBLE CAUSE 1. Switch on device is turned off . 3. Signals from transmitter will reset receiver to the following information available: Model Number, Date of Purchase, and Place of Purchase. Device is turned on . 3.
Change codes on randomly. Check battery charge and replace if necessary. 7. Next transmission from transmitter are set the same. 8.
You may...
User Guide - Page 10
... for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping...Repair service, adjustment and calibration due to province. For a period of two years from state to state or province to misuse, abuse or negligence, light bulbs, batteries, and other equipment and components that a customer uses in conjunction with our products. REPAIR OR REPLACEMENT...
Zenith SL-6030-WH5 Reviews
We have not received any reviews for Zenith yet.