Zenith SL-6037-WH - Heath - Wireless Command Support and Manuals
Get Help and Manuals for this Zenith item
View All Support Options Below
Free Zenith SL-6037-WH manuals!
Problems with Zenith SL-6037-WH?
Ask a Question
Free Zenith SL-6037-WH manuals!
Problems with Zenith SL-6037-WH?
Ask a Question
Popular Zenith SL-6037-WH Manual Pages
User Guide - Page 1
.... Simply determine which transmitter(s) you would like to have the same code and group setting to your particular product. Heath®/Zenith wireless lighting controls are designed to a different code. Code Settings
Note: Most single system installations will not require any other , set the code setting to the following products: • Transmitters
- Transmitter(s) and receiver(s) must...
User Guide - Page 2
...®
ON-TIME
Off 3Hr Dusk to TEST 1 5
Dawn
(Mins)
Solar Powered Motion Sensor
Code Switches
Floodlight
ON 1 2 3 4
Code Switches
Indoor Plug-In Converter
Note: The "X" has been placed on the switches to help clarify the code settings on the previous page.
ON 1 2 3 4
Close-Up of Typical Code Switch (Factory Default Setting is Off)
598-1271-01
User Guide - Page 3
...above
instructions.... Remove battery tab. 3.
Only use alkaline batteries. Replace battery compartment cover by rotating clear solar
panel cover counterclockwise...MAX NIGHT DAY
ONLY NIGHT
O N
Dawn
DUALBRITE®
CODE 1 2 3 4
Lock
Unlock
CODE 1 2 3 4
RANGE DETECT MIN MAX NIGHT DAY
... 1 5
Dawn
(Mins) Clear Solar Panel Cover
Setting Controls
The controls are located on the bottom of...
User Guide - Page 4
... triggering
the sensor, adjust the RANGE dial as needed to avoid false
triggering. Installing Solar Motion Sensor
1. Attach the sensor unit to 6 hours of
desired coverage....on the ground and press into
the ground.
6. Note: If you want to install
the motion sensor. Continue with testing after installation, al- DualBrite® Dimmer Control
Light comes on half power for the selected...
User Guide - Page 5
... the control. • Nearby large, light colored objects reflecting light may result in some environments. 4. Set the ON-TIME control to the TEST position. The LED indicator light should flash when motion is detected (see illustration, page 4, for location of view. Turn the RANGE control to the mid position and ON-TIME...
User Guide - Page 6
...MANUAL modes. Plug in light you wish to Brightest, Full On). • Remembers last selected dim setting. • Not for 120VAC/60Hz supply voltage. • Light can be dimmed when used with receiver (see transmitter instructions...OFF. 4.
A signal will be operated manually. 5. The alarm sounds only when the receiver is adjusted by the wireless motion sensor and entry switch. Remote ...
User Guide - Page 7
...the factory setting. Secure with.... • Install fixture in accordance with local codes. Fixture should...Install the mounting strap as shown. Thread the small end of the slots on fixture. Caulk the wall plate mounting surface with receiver (see transmitter instructions). Note: The plastic hanger can be used with silicone weather sealant. 8. Mounting Strap
White to White...
User Guide - Page 8
... device may also write* to correct state. 2.
Does not respond immediately after installation.
5.
SOLUTION
1. Troubleshooting Guide
POSSIBLE CAUSE 1. Dip switches on randomly. Switched device is turned on . 3.
If you experience a problem, follow this Product
Regulatory Information
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada...
User Guide - Page 9
... to change specifications at any time without incurring any malfunction caused by this warranty in conjunction with our products. Some states or provinces do not allow the exclusion or limitation of use, unauthorized service, or return shipping charges. This warranty covers only HeathCo LLC assembled products and is required for inconvenience, installation, setup time...
Zenith SL-6037-WH Reviews
We have not received any reviews for Zenith yet.