Zenith SL-6032-WH-A - Heath - 240-Degree Wireless Motion Sensor Support and Manuals
Get Help and Manuals for this Zenith item
View All Support Options Below
Free Zenith SL-6032-WH-A manuals!
Problems with Zenith SL-6032-WH-A?
Ask a Question
Free Zenith SL-6032-WH-A manuals!
Problems with Zenith SL-6032-WH-A?
Ask a Question
Popular Zenith SL-6032-WH-A Manual Pages
User Guide - Page 1
...Floodlight
This manual includes operating instructions for switch locations.
( - Please read all instructional information and note any change to your particular product. Features
• Products are 8 codes available by changing the settings of switches 1 through 3 set the code. Code Settings
Note: Most single system installations will not require any specific information pertaining...
User Guide - Page 2
... "X" has been placed on the switches to help clarify the code settings on the previous page. ON 1 2 3 4
Close-Up of Typical Code Switch (Factory Default Setting is Off)
598-1306-02 Code Switch Locations
Code Switches
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
180° Motion Sensor
Code Switches
CODES
DETECT
1 2 3 4
DAY NIGHT NIGHT ONLY
240° Motion Sensor...
User Guide - Page 3
...Replace battery compartment cover by reversing the above instructions. Make sure unit has an unobstructed view.
Install 2 AA batteries according to a sturdy object (i.e. Attach motion sensor mounting bracket to polarity markings inside the battery compartment. Note: Attach mounting bracket vertically if connecting to 100 feet (30 m) away. To set... (Depending
upon model). • ...
User Guide - Page 4
...Dawn IMPORTANT: Avoid Aiming Motion Sensor At: • Objects that change the coverage area. Set the ON-TIME control to the TEST position. Determine the amount of the motion sensor....®
control). • Off • 3 Hours • 6 Hours • Dusk to flash. Set the DETECT control switch to TEST mode. Slide the ON-TIME control to change temperature rapidly, such as heating...
User Guide - Page 6
... the junction box with 120 volt incandescent or halogen bulbs.
Select light switch to be replaced by a qualified electrician.
In addition, some local build-
See rating label on switch... the wires (see illustration).
ing codes may need to bend the wires to fit inside the box. ing upon switch purchased. You may require installation by wall switch receiver.
2. Remove...
User Guide - Page 7
.... Push either the top or bottom of DIM button. Push and release top of DIM button and release. To recall last DIM setting from 15% to decrease brightness. Bulb Replacement Move the power disconnect switch to increase brightness. CAUTION: Do not exceed the maximum load limits listed above.
598-1306-02
Note...
User Guide - Page 8
... wires from the factory setting. Secure with local codes. Align the cover plate... and cover plate gasket. Push the rubber plug firmly into one of the plastic hanger through the large gasket holes. 5. Fixture should be used with receiver (see transmitter instructions...• Minimal wiring required. • Install fixture in the lamps, do not overtighten. ...
User Guide - Page 9
... replace if necessary. 7. Next transmission from transmitter are set the same. 8. Change codes on randomly. You may not cause harmful interference, and (2) this guide. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please have the following two conditions: (1) this device may also write* to 4:30 PM CST (M-F). Troubleshooting Guide...
User Guide - Page 10
... equipment and components that a customer uses in its entirety. Unauthorized service or modification of the product or of any obligation to you specific legal rights. REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HeathCo LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL...
Zenith SL-6032-WH-A Reviews
We have not received any reviews for Zenith yet.