Zenith HD-9250-BZ-C - Heath - 270 Degree Journeyman Motion Sensing Security Light Support and Manuals
Get Help and Manuals for this Zenith item
This item is in your list!
View All Support Options Below
Free Zenith HD-9250-BZ-C manuals!
Problems with Zenith HD-9250-BZ-C?
Ask a Question
Free Zenith HD-9250-BZ-C manuals!
Problems with Zenith HD-9250-BZ-C?
Ask a Question
Popular Zenith HD-9250-BZ-C Manual Pages
User Guide - Page 1
All Metal Motion
Sensor Light Control
Model HD-9250
© 2008 HeathCo LLC
598-1187-02
User Guide - Page 2
Contents
Introduction 3 Package Contents 4
Installation...5 Wall Mount 5 Eave Mount 5 Crossbar Mounting Bracket 6 Standard Wiring 6 Controlling Non-Motion Sensing Fixtures 7 Finish Mounting 8 Specifications 8
Test and Adjustment 9 Expected Coverage 10
Operation...12 Troubleshooting Guide 13 JourneyMan® Lifetime Warranty 14
--
598-1187-02
User Guide - Page 3
...in 1.25 Mega Watt surge protection. ☞ A.S.I.C. (Application Specific Integrated Circuit) design allows more infrared light improving detection sensitivity. ...confident with the durability of coverage range. ☞ Manual override to control other lights with your convenience with built.... ☞ Extremely wide angle coverage (up to set the time lights stay on after motion has been ...
User Guide - Page 4
Package Contents
• Motion Sensor Light Fixture • Manual • Hardware Pack
1 Gasket 1 Hanger 1 Crossbar Mounting Bracket
4 Wire nuts 2 #6-32 X 3/4" Screws
(for small rectangular boxes) 2 #8-32 X 3/8" Screws
(for circular or octagon boxes) 2 #10-24 X 1/2" ...
User Guide - Page 5
... to use the Manual Override feature you will need to this illustration.
❒ Finger tighten the thumbscrews at this time.
598-1187-02
--
Wall Mount
Eave Mount
❒ Loosen the thumbscrews holding the sensor
head and lampheads.
❒ Adjust the various parts so that the fixture
looks similar to install the fixture on...
User Guide - Page 6
... at the fuse or circuit breaker. ❒ Remove the existing light fixture (if appli-
Junction Box
Green ground wire to the fixture wires. cable).
❒ Install the mounting bracket as shown using
two screws supplied in hardware pack that fit your JourneyMan® fixture, DO NOT connect the RED wire or...
User Guide - Page 7
NOTE: All wiring between fixtures should be run in accordance with a sensor rated
for 1000 Watts. Since the fixture is provided with the National Electrical Code (Canadian Electrical Code in the fixture. nected and determined their maximum ratings, add these ratings up. For instance, if you have 3 fixtures rated 100 Watts, 150 Watts...
User Guide - Page 8
... plug firmly into place. ❒ If not installed on a weatherproof box, caulk
between the cover plate and mounting surface with Range Boost. Rubber Plug
Specifications
Range 70 feet (21.0 m); 100 feet (30...hole. TEST, AUTO, and MANUAL OVERRIDE
Time Delay 1, 5, 20 minutes
HeathCo LLC reserves the right to discontinue products and to change specifications at any time without incurring any...
User Guide - Page 10
...)
Sensor
Least Sensitive
Most Sensitive
8 ft. (2.4 m)
-10-
70 ft. (21.0 m) With RANGE Set to side.
Loosen the thumbscrews and readjust the sensor as needed to motion across its field of TIME (1, ...10066; Walk through the coverage area noting where you may be aiming straight out. ❒ Set the amount of view. Tighten the thumbscrews (finger tight) when you want the lights to ...
User Guide - Page 12
...the center of its adjustment. Operation
Mode:
On-Time: Works: Day Night
MANUAL MODE
Test
5 Sec
xx
Manual Mode only works at dawn.
TEST MODE
Slide the ON-TIME switch to... will be in the 1,
5, or 20 minute position.
Manual Until Dawn*
x
night because daylight returns
x
the sensor to AUTO.
* resets to the desired setting.
TEST 1 5 20
AUTO MODE
ON TIME Put the ON...
User Guide - Page 13
...installed in a relatively dark 1. reflective surface.
1. Control may be turning the light control on and off
POSSIBLE CAUSE(S)
CORRECTIVE ACTION(S)
1. automobile traffic.
2. Control is in Test.
2. Set control switch to warm up .
4. Tighten or replace...
location. Re-aim sensor or use lens shield. Troubleshooting Guide
SYMPTOM Lights will not come on
Lights come on ...
User Guide - Page 14
... may also have the following information available: Model Number, Date of Purchase, and Place of any malfunction caused by this warranty in conjunction with our products. Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other rights which gives you specific legal rights. THIS WARRANTY IS EXPRESSLY IN...
Zenith HD-9250-BZ-C Reviews
Do you have an experience with the Zenith HD-9250-BZ-C that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Zenith yet.
Earn 750 points for your review!