Zenith SL-6030-WH5 Support Question
Zenith SL-6030-WH5 Support Question
Find answers below for this question about Zenith SL-6030-WH5 - Heath - Wireless Command Motion Sensor.Need a Zenith SL-6030-WH5 manual? We have 1 online manual for this item!
Question posted by sanks2u on October 9th, 2012
Interchangable Sensors
My old unit sensor seems to be in a state of malfunction. If I purchase a new SL 6030 TX, will the new sensor communicate with my outdoor light? Il there a need to change frequencies between old lights and new sensors?
Current Answers
Related Zenith SL-6030-WH5 Manual Pages
User Guide - Page 1
...® guidelines when DualBrite® function is off. Please read all instructional information and note any change to the following products: • Wireless Transmitters (Indoor / Outdoor)
- 180° Motion Sensor - 240° Motion Sensor • Receivers -
Heath®/Zenith wireless lighting controls are UL/cUL and/or FCC/IC tested and approved. • Operational range of...
User Guide - Page 2
... Code Switch (Factory Default Setting is Off)
598-1306-02 Code Switch Locations
Code Switches
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
180° Motion Sensor
Code Switches
CODES
DETECT
1 2 3 4
DAY NIGHT NIGHT ONLY
240° Motion Sensor
Code
Switches
ON
Wall Switch Receiver
Code Switches
LAMP MODE switches
RAINTIGHT
ã THIS END UP...
User Guide - Page 3
.... • Controls receivers up to polarity markings inside the battery compartment. Install 2 AA batteries according to 100 feet (30 m) away. Install motion sensor mounting bracket where motion detection is desired. Make sure unit has an unobstructed view. Note: Attach mounting bracket vertically if connecting to a sturdy object (i.e. Tighten clamp screw. Mounting Bracket Socket
Clamp...
User Guide - Page 4
... objects reflecting light may result in
front of motion sensor. Note: Meets the ENERGY STAR® guidelines when DualBrite® function is detected (see illustration for location of time desired for selected time after motion is detected (1 or 5 minutes). Set the ON-TIME control to Dawn IMPORTANT: Avoid Aiming Motion Sensor At: • Objects that change the...
User Guide - Page 5
... Range
Maximum Coverage Angle
240° Motion Sensor Coverage Area
Aim Sensor Down for Short Coverage
Aim Sensor Higher for Long Coverage
Adjusting Motion Sensor Coverage
598-1306-02
ENGLISH
8 ft. (2.4 m)
180°
Motion
Motion
70 ft. (21 m) Maximum Range
Maximum Coverage Angle
180° Motion Sensor Coverage Area
Sensor
Sensor
Least Sensitive
Most Sensitive
The detector is...
User Guide - Page 6
...light switch circuit. Remove the existing wall plate and switch. Disconnect the two
power wires and the ground wire.
ing codes may need to bend the wires to 500 Watt maximum incandescent load depend- ing upon switch purchased. If necessary, strip away 1/2" of insulation from the old... electrician about installation. Important: When ganging these units, they are secure and that no bare wires...
User Guide - Page 7
...Verify the power disconnect switch is switched on. 3. Push the ON (top) button and release. The light should turn on at 50% brightness (or last setting). 5. Note: DIM setting remembers last setting used...% in the ON (right side)
position. 2.
Push the OFF (bottom) button and release. The light should turn on
full bright. Push either the top or bottom of DIM button. Note: There are ...
User Guide - Page 8
... only. Route the wires from the factory setting.
Remove the existing light fixture. 2.
Light instantly comes on fixture. Secure with silicone weather sealant.
9. Floodlight
...Features and Ratings: • Up to 150 Watt maximum
incandescent load or 240 Watt maximum halogen load (up to off when motion...
User Guide - Page 9
... device.
1. Change codes on . 3. If the problem persists, call 1-800-858-8501 (English speaking only) for 90 second initialization period
(remote motion sensor). 5.
Dip ...Purchase, and Place of Industry Canada. Short term power line failure.
2. Another transmitter on .
2. Verify circuit breaker or fuse is subject to correct state.
2. Change codes on transmitter and receiver units...
User Guide - Page 10
... at any time without incurring any malfunction caused by this warranty in products... to discontinue products and to change specifications at no charge to ... a period of purchase, any obligation to incorporate new features in its entirety. Some states or provinces do...state to state or province to province. Repair service, adjustment and calibration due to misuse, abuse or negligence, light ...
Similar Questions
Sl 6030 Tx Motion Sensor-floodlight
my light does not turn off. The transmitter seems to be functioning..If receiver us faulty, do i nee...
my light does not turn off. The transmitter seems to be functioning..If receiver us faulty, do i nee...
(Posted by Jfalk1 5 years ago)
Replacement For Sl-6030-tx
What is the replacement for the zenith SL-6030-TX motion sensor
What is the replacement for the zenith SL-6030-TX motion sensor
(Posted by F58lrpl75ranger 7 years ago)
What If We Put New Batteries In And It Is Still Not Working
what if I put new batteries in and it's still doesn't work
what if I put new batteries in and it's still doesn't work
(Posted by bustos1155 8 years ago)
Has The Sl-6053 Been Discontinued Or Is It Just Out Of Stock?
(Posted by jclout4153 9 years ago)
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)