Zenith SL-6053-WH Support Question
Zenith SL-6053-WH Support Question
Find answers below for this question about Zenith SL-6053-WH - Heath - Wireless Command.Need a Zenith SL-6053-WH manual? We have 1 online manual for this item!
Question posted by jclout4153 on February 26th, 2015
Has The Sl-6053 Been Discontinued Or Is It Just Out Of Stock?
The person who posted this question about this Zenith product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TheWiz on February 26th, 2015 1:12 PM
TheWiz
Member since:
October 13th, 2011 Points: 25,383,424
Member since:
October 13th, 2011 Points: 25,383,424
It's out of stock at most stores so I would assume that it's been discontinued. If you still want to purchase it though, it's available from here.
Related Zenith SL-6053-WH Manual Pages
User Guide - Page 1
... to match. This manual applies to your particular product.
Heath®/Zenith wireless lighting controls are 8 codes available by changing the settings of... specific information pertaining to the following products: • Wireless Transmitters (Indoor / Outdoor)
- 180° Motion Sensor - 240° Motion Sensor -
Transmitter(s)/ Receiver(s) Code
Group "A"
Group "A" © 2008 HeathCo...
User Guide - Page 2
Code Switch Locations
Code Switches
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
180° Motion Sensor
Code Switches
CODES
DETECT
1 2 3 4
DAY NIGHT NIGHT ONLY
240° Motion Sensor
CR2032 3 VOLTS
ON 1 2 34
Code Switches Entry Switch
Code Switches
LAMP MODE switches
RAINTIGHT
ã THIS END UP
OUTDOOR USE ONLY.
ON 1 2 3 4
Close-Up of ...
User Guide - Page 3
... . To set the detection mode, remove battery compartment cover by reversing the above instructions. Tighten clamp screw. ENGLISH
180° and 240° Motion Sensors
180° Motion Sensor
240° Motion Sensor
Features: • No wiring required. • Up to 70 feet sensing range, 180° or 240° Coverage (Depending
upon model). • Adjustable...
User Guide - Page 4
... day time: A. Check Operation. Loosen the clamp screw and move the motion sensor to Dawn IMPORTANT: Avoid Aiming Motion Sensor At: • Objects that change the coverage area. Note: When using... Indicator
ON-TIME Control
ON-TIME (MINUTES)
5 1 TEST
RANGE
MAX
MIN
180° Motion Sensor Controls
Range Control
LED Indicator
DualBrite® Control
RANGE
MAX
MIN
DUSK TO 6 3 OFF...
User Guide - Page 5
... Range
Maximum Coverage Angle
240° Motion Sensor Coverage Area
Aim Sensor Down for Short Coverage
Aim Sensor Higher for Long Coverage
Adjusting Motion Sensor Coverage
598-1306-04
ENGLISH
8 ft. (2.4 m)
180°
Motion
Motion
70 ft. (21 m) Maximum Range
Maximum Coverage Angle
180° Motion Sensor Coverage Area
Sensor
Sensor
Least Sensitive
Most Sensitive
The detector is...
User Guide - Page 9
...Do not exceed the maximum load limits listed above. 11. Activate transmitter being used to off when motion is detected:
• NORMAL
or
-
Light starts dim and gradually increases to green ground screw... mounting strap. 3. WARNING: Turn power off twice before turning on effects) available when motion is no longer detected and
after selected ON-TIME.
• FLASH
- Remove the ...
User Guide - Page 10
... fuse is turned on .
Does not respond immediately after installation.
5. Device is out of Purchase. No Service Parts Available for 90 second initialization period
(remote motion sensor). 5.
Change codes on transmitter and receiver units. SYMPTOM Device does not come on . 3.
User Guide - Page 11
... TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Not Covered - You may not apply to you. HeathCo LLC reserves the right to discontinue products and to change specifications at no charge to you specific legal rights.
Similar Questions
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Heath Zenith Sl-4305-wh Wiring Schematic
I would like to deactivate to motion sensor on automatic
I would like to deactivate to motion sensor on automatic
(Posted by redolds98 11 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)
Zenith Sl-6040-wh-b Configurations
Where can I find more information? Such as number of sensors that can be used
Where can I find more information? Such as number of sensors that can be used
(Posted by johannesgrande 12 years ago)
Using Two Sl 6106 Wh Switches
I have an application now operated using convential 3 way switches--I would like to use two sl 6106 ...
I have an application now operated using convential 3 way switches--I would like to use two sl 6106 ...
(Posted by mrnester 13 years ago)