Zenith SL-4305-WH Support Question
Zenith SL-4305-WH Support Question
Find answers below for this question about Zenith SL-4305-WH - Heath - Motion-Activated Five-Sided Porch Light.Need a Zenith SL-4305-WH manual? We have 1 online manual for this item!
Question posted by emvilla on November 30th, 2019
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
Current Answers
Answer #1: Posted by Odin on December 2nd, 2019 11:46 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
Can't be done by the user. (Sorry.) The best you can do is minimize the sensitivity and the on-time--see https://www.manualslib.com/manual/67377/Heath-Zenith-Sl-4305.html?page=4#manual. An appliance technician may be able to effect the deactivation: for referral use the contact information at https://www.contacthelp.com/zenith/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Zenith SL-4305-WH Manual Pages
User Guide - Page 1
... one minute, then back on the sensor to AUTO.
Before installation, record the model number listed inside the fixture.Attach receipt in case of possible warranty issues.
ON-TIME
TEST 1 5 10 MIN
MANUAL MODE
Manual mode only works at night because daylight returns the sensor to TEST. Motion Sensing Porch Light
SL-4305
Features
• Light comes on .
User Guide - Page 2
...Universal Mounting Bracket Junction Box Screw
Fixture Screw (Tightened Finger Tight)
Decorative Nut
SENSITIVITY LO -
Light Fixture Cover
Junction Box
Decorative Nut
3. Twist and secure wires with the two screws provided. Remove two decorative nuts from this motion sensor fixture.
2. M - Install universal Mounting Bracket
For best performance, mount the fixture at circuit breaker...
User Guide - Page 3
... the lamp(s) currently installed in accordance with the National Electrical Code through conduit or another standard or motion sensing light fixture(s).
See the following wiring diagrams for Motion Sensor -
300 Watts (200 Watts Remaining)
IMPORTANT: When determining the maximum lamp wattage rating of the system.
Note: All wiring should be controlled, refer to the...
User Guide - Page 4
... and void your warranty. After switches are when the lights turn on after motion is detected (1, 5, or 10 minutes).
360°
8 ft. (2.4 m)
Decorative Nut
SENSITIVITY LO -
Set the SENSITIVITY switch to the "M" position and the ON-TIME switch to install the cover. HI
Sensor Lens
TEST 1 5 10 MIN
ON-TIME
3. Walk through the...
User Guide - Page 5
... shield to change the effective range of lens shield required, apply small sections one side of this light fixture detects "motion"
by 30 degrees. Remove paper backing from one at a time. Bulb Type Candelabra Base, Type "B", 25 Watt Maximum Sensor Capacity Up to 30 ft. (9.1 m) [varies with surrounding temperature]. However, following are examples
of...
User Guide - Page 6
... is set too high. (Re-
reason.
(Reduce sensitivity.)
2. duce sensitivity.)
SYMPTOM
POSSIBLE CAUSE
Light stays on 1. There is turned off . Heat being reflected from other
lights at the sensor.
598-1184-04 sor. (Reduce sensitivity.)
2. relatively dark location.
2. Sensor may be affecting the sen- Sensitivity is
a new installation.
air vent, dryer vent, or...
User Guide - Page 7
... visit our Web site at: www.hzsupport. No Service Parts Available for this warranty. Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other equipment and components that a customer uses in conjunction with our products. Unauthorized service or modification of the product or of five...
Similar Questions
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
How To Turn On Sensor
(Posted by AWJ619 11 years ago)
Heath Zenith Sl-4305-wh Wiring Schematic
I would like to deactivate to motion sensor on automatic
I would like to deactivate to motion sensor on automatic
(Posted by redolds98 11 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)
Using Two Sl 6106 Wh Switches
I have an application now operated using convential 3 way switches--I would like to use two sl 6106 ...
I have an application now operated using convential 3 way switches--I would like to use two sl 6106 ...
(Posted by mrnester 13 years ago)