Zenith SL-6053-WH Support Question
Zenith SL-6053-WH Support Question
Find answers below for this question about Zenith SL-6053-WH - Heath - Wireless Command.Need a Zenith SL-6053-WH manual? We have 1 online manual for this item!
Question posted by dowellpj on July 10th, 2013
Three Flash Error Code.
I have two 240 degree sensors. One works fine, the other gives me three flashes on the LED light continious. Is this an error code? Can I fix or reboot it? Help and Thanks,
John
Current Answers
Related Zenith SL-6053-WH Manual Pages
User Guide - Page 1
...
Lighting Controls
PAGE REFERENCE GUIDE
Page 3
Page 6
Page 7
Page 9
Meets the ENERGY STAR® guidelines when DualBrite® function is off. Code Settings, System 2 Note: When operating more than one system independently of Switch)
Example 1 - Indicates Position of each system to the following products: • Wireless Transmitters (Indoor / Outdoor)
- 180° Motion Sensor - 240...
User Guide - Page 2
... switches to help clarify the code settings on the previous page.
ON 1 2 3 4
Close-Up of Typical Code Switch (Factory Default Setting is Off)
598-1306-04 Code Switch Locations
Code Switches
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
180° Motion Sensor
Code Switches
CODES
DETECT
1 2 3 4
DAY NIGHT NIGHT ONLY
240° Motion Sensor
CR2032 3 VOLTS
ON 1 2 34
Code Switches Entry...
User Guide - Page 3
...Bracket Socket
Clamp Screw
Swivel Ball Mount
Mounting Bracket
Mounting Screw Nut
Sensor
Installing Motion Sensor (180° Motion Sensor Shown)
Detect Control
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
CODES
DETECT
1 2 3 4
DAY NIGHT NIGHT ONLY
180° Motion Sensor (Rear View)
240° Motion Sensor (Rear View)
Battery Compartment
598-1306-04
Installing Batteries • Before...
User Guide - Page 4
...LED indicator light should flash when motion is detected (see illustration for selected time after motion is off feature. Loosen the clamp screw and move the motion sensor... light colored objects reflecting light may result in
front of LED light). 2.
Walk in some environments. Adjust Motion Sensor. Check Operation. DualBrite® Dimmer Control (240° Motion Sensor Only)
Light...
User Guide - Page 5
...176; Motion Sensor Coverage Area
Sensor
Sensor
Least Sensitive
Most Sensitive
The detector is most sensitive to motion across its field of view. Motion Sensor Sensitivity
8 ft. (2.4 m)
240°
70 ft. (21 m) Maximum Range
Maximum Coverage Angle
240° Motion Sensor Coverage Area
Aim Sensor Down for Short Coverage
Aim Sensor Higher for Long Coverage
Adjusting Motion Sensor Coverage...
User Guide - Page 6
... be mounted on the face of movement. Battery Replacement
between transmitter and magnet is shipped with small, flat-blade
screwdriver. Verify red LED on transmitter flashes momentarily and receiver turns light on type of the transmitter
and magnet must be used to simulate door or window being closed. Important Considerations: • Entry transmitter...
User Guide - Page 7
... wire. In addition, some local build- ing codes may need to bend the wires to control a receptacle, a motor-operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance.
4. Wall... 10. Turn on wall switch receiver with screws (short) provided. 11. Select light switch to the light switch circuit. Remove the existing wall plate and switch. CAUTION: Do not connect ...
User Guide - Page 8
...button and release. Note: The DIM setting defaults to increase brightness.
Operation 1. The light should turn on
full bright. Replace bulb(s). Verify the power disconnect switch is connected ...) button and release. Bulb Replacement Move the power disconnect switch to 90% brightness.
6. The light should turn off. 4. Push either the top or bottom of a power failure. Set desired ...
User Guide - Page 9
...light turn -on the mounting strap. 3. WARNING: Risk of the slots on effects) available when motion is no longer detected and
after selected ON-TIME.
• FLASH... screw on .
• SOFT
- Secure with local codes. Screw incandescent bulb up to 75 Watt maximum incandescent, ...8226; Up to 150 Watt maximum
incandescent load or 240 Watt maximum halogen load (up to rated wattage into...
User Guide - Page 10
... only) for 90 second initialization period
(remote motion sensor). 5. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please have the following two conditions: (1) this device may not cause harmful interference, and (2) this guide. Weak battery in the transmitter.
7. Verify code settings on randomly. Next transmission from transmitter...
User Guide - Page 11
... TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other rights which gives you . Please keep your dated sales receipt, it is required for inconvenience, installation, setup time, loss of use, unauthorized service, or return...
Similar Questions
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Has The Sl-6053 Been Discontinued Or Is It Just Out Of Stock?
(Posted by jclout4153 9 years ago)
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
Heath Zenith Sl-4305-wh Wiring Schematic
I would like to deactivate to motion sensor on automatic
I would like to deactivate to motion sensor on automatic
(Posted by redolds98 11 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)