Zenith SL-6053-WH Support Question
Zenith SL-6053-WH Support Question
Find answers below for this question about Zenith SL-6053-WH - Heath - Wireless Command.Need a Zenith SL-6053-WH manual? We have 1 online manual for this item!
Question posted by kestridge on May 27th, 2011
Help With Dual Brite Lites
Good morning. I have 6 dual brite lights (black lantern style) around my newly remodeled home. I have decided that they are not appropriate for my back deck. I want to use them as a regular light that goes on and stays on when I flip the switch. What suggestions do you have? (My contractor destroyed all of the instruction sheets, but told me to leave them in "test mode" which, after a few seconds, makes the lights blink.) Thanks.
Current Answers
Related Zenith SL-6053-WH Manual Pages
User Guide - Page 1
...Indoor / Outdoor)
- 180° Motion Sensor - 240° Motion Sensor - Transmitter(s) and receiver(s) must have control which receiver(s) and set the code. Switches 1 through 3. Indicates Position of remote controlled products. Transmitter(s)/ Receiver(s) Code
Group "A"
Group "A" © 2008 HeathCo LLC
Group "B"
598-1306-04 Heath®/Zenith wireless lighting controls are designed to...
User Guide - Page 2
...; Motion Sensor
CR2032 3 VOLTS
ON 1 2 34
Code Switches Entry Switch
Code Switches
LAMP MODE switches
RAINTIGHT
ã THIS END UP
OUTDOOR USE ONLY.
FOR WALL AND CEILING MOUNT ONLY
SUITABLE FOR WET LOCATION MADE IN CHINA
Floodlight
Code
Switches
ON
Wall Switch Receiver
Note: The "X" has been placed on the switches to help clarify...
User Guide - Page 3
... and night or night only. Select Night or 24 Hour Mode These motion sensors are able to a sturdy object (i.e. Aim motion sensor toward area where detection is
desired. Install motion sensor mounting bracket where motion detection is desired. Using a Philips-head screwdriver, loosen the clamp screw on motion sensor into mounting bracket socket (Note: You should hear a snap). To set...
User Guide - Page 4
... through coverage area noting where you want the connected device to accent mode. 1. Loosen the clamp screw and move the motion sensor to flash.
These air sources could cause false triggering. • Areas where pets or traffic may trigger the control. • Nearby large, light colored objects reflecting light may result in some environments. LED...
User Guide - Page 5
...176; Motion Sensor Coverage Area
Sensor
Sensor
Least Sensitive
Most Sensitive
The detector is most sensitive to motion across its field of view. Motion Sensor Sensitivity
8 ft. (2.4 m)
240°
70 ft. (21 m) Maximum Range
Maximum Coverage Angle
240° Motion Sensor Coverage Area
Aim Sensor Down for Short Coverage
Aim Sensor Higher for Long Coverage
Adjusting Motion Sensor Coverage...
User Guide - Page 6
... 3 VOLTS CR2032 3 VOLTS
Tape Mounting: Apply large piece of door or window in alignment
(see Troubleshooting Guide.
4.
receiver should be used for indoor use magnet
extension and two long screws (provided) to automatically turn the light on the face of Moof vMoevmemeennt t
pop up
Mounting Configurations and Possible Directions of transmitter 4. With typical...
User Guide - Page 7
... for exact load rating. • Not for use with screws (short) provided. 11.
CAUTION: To reduce the risk of wires. 5. Connect one of the black power wires from the old switch. You may ...not connect neutral (white wire) to the light switch circuit. Push excess wiring into junction box. 10. Remove the existing wall plate and switch. Use one of the supplied wire connectors to the...
User Guide - Page 8
The light should turn off. 4. ...or bottom of DIM button to 50% in the ON (right side)
position. 2. The light should turn on at 50% brightness (or last setting). 5. Push and release top of ... brightness. CAUTION: Do not exceed the maximum load limits listed above.
598-1306-04 The light should turn on . 3. Operation 1. Push and release bottom of DIM button and release. Note...
User Guide - Page 9
...to White
Black to Black
Rubber Plug
Gasket
Junction box ground wire to full
brightness. Light instantly ...used to the desired light turn -on the mounting strap. 3. Light flashes on effect (Normal, Soft, Flash). 4. Push the rubber plug firmly into place.
8.
Lamp Modes There are three lamp modes (light turn -on then off when motion is detected:
• NORMAL
or
- Light...
User Guide - Page 10
... 5, 6, and 7 above . 1. Another transmitter on . Test using different device.
1. Next transmission from transmitter are set the same.... Interrupted by the party responsible for 90 second initialization period
(remote motion sensor). 5. Dip switches on randomly. Short term power line failure.
... that may also want to visit our Web site at 1-800-858-8501 (English speaking only),...
User Guide - Page 11
...components that a customer uses in conjunction with our products. This warranty covers only HeathCo LLC assembled products and is not extended to misuse, abuse or negligence, light bulbs, batteries, and...OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Repair ...
Similar Questions
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Has The Sl-6053 Been Discontinued Or Is It Just Out Of Stock?
(Posted by jclout4153 9 years ago)
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
How To Wire Health Motion Sensor Sl-5410a
(Posted by ranyog 9 years ago)
Three Flash Error Code.
I have two 240 degree sensors. One works fine, the other gives me three flashes on the LED light con...
I have two 240 degree sensors. One works fine, the other gives me three flashes on the LED light con...
(Posted by dowellpj 10 years ago)