Operating Instructions
Page 5
...Rear/Right Side/Bottom 10 Control Panel 12 Connector Panel 12 Remote Commander 13 Setting Up and Projecting Installing the Projector 16 Connecting the Projector 17 Connecting with a Computer ......17 Connecting with a VCR or 15k RGB/Component Equipment 19 Selecting the Menu ...Language ..........21 Projecting 23 Effective Tools for Your Presentation 27 The INSTALL SETTING Menu ..... 34 The INFORMATION Menu 35 Maintenance Maintenance 36 Replacing the Lamp...
...Rear/Right Side/Bottom 10 Control Panel 12 Connector Panel 12 Remote Commander 13 Setting Up and Projecting Installing the Projector 16 Connecting the Projector 17 Connecting with a Computer ......17 Connecting with a VCR or 15k RGB/Component Equipment 19 Selecting the Menu ...Language ..........21 Projecting 23 Effective Tools for Your Presentation 27 The INSTALL SETTING Menu ..... 34 The INFORMATION Menu 35 Maintenance Maintenance 36 Replacing the Lamp...
Operating Instructions
Page 36
... tilt the lamp. Note Be sure that the projector is stable after using the projector Turn off the projector with qualified Sony personnel. • Pull out the lamp by holding the handle. When replacing the lamp after turning it remains horizontal, then pull straight up The lamp life varies depending on conditions of use. When you replace the lamp, wait for...
... tilt the lamp. Note Be sure that the projector is stable after using the projector Turn off the projector with qualified Sony personnel. • Pull out the lamp by holding the handle. When replacing the lamp after turning it remains horizontal, then pull straight up The lamp life varies depending on conditions of use. When you replace the lamp, wait for...
Operating Instructions
Page 37
Remove dust from the outside of the lamp. • The power will not turn the projector to standby mode. 8 Press the following order for less than five seconds each: RESET, Fold the handle. Cleaning the Air Filter The air filter should ... holes with a vacuum cleaner. Tighten the screws. 4 Insert the new lamp all the way in until it is not secured properly. 5 Close the lamp cover and tighten the screws. 6 Turn the projector back over. 7 Connect the power cord and turn on if the lamp is securely in the following keys on the remote commander...
Remove dust from the outside of the lamp. • The power will not turn the projector to standby mode. 8 Press the following order for less than five seconds each: RESET, Fold the handle. Cleaning the Air Filter The air filter should ... holes with a vacuum cleaner. Tighten the screws. 4 Insert the new lamp all the way in until it is not secured properly. 5 Close the lamp cover and tighten the screws. 6 Turn the projector back over. 7 Connect the power cord and turn on if the lamp is securely in the following keys on the remote commander...
Operating Instructions
Page 40
... adjusted properly. The picture is not clear. • Picture is too dark. • Contrast or brightness has not been adjusted properly. c Leave the projector for about two hours with a new one (see page 32). The picture flickers. • "Dot Phase" in the "Adjust Picture..." c Set "Color...system being input (see page 25). in the SET SETTING menu to "Off." menu properly (see page 29). • The lamp has burnt or dims. c Replace the lamp with the power on . Symptom Cause and Remedy "Please check INPUT-A setting." c Set "Status" in the SET SETTING menu is...
... adjusted properly. The picture is not clear. • Picture is too dark. • Contrast or brightness has not been adjusted properly. c Leave the projector for about two hours with a new one (see page 32). The picture flickers. • "Dot Phase" in the "Adjust Picture..." c Set "Color...system being input (see page 25). in the SET SETTING menu to "Off." menu properly (see page 29). • The lamp has burnt or dims. c Replace the lamp with the power on . Symptom Cause and Remedy "Please check INPUT-A setting." c Set "Status" in the SET SETTING menu is...
Operating Instructions
Page 41
... TEMP/FAN indicator • The fan is detached. Message Meaning and Remedy High temp.! c Check to "Component." c Replace the lamp. c Replace with qualified Sony personnel. c Attach the cover securely (see page 33). flashes. c Input a signal that is within the range of ... LAMP/COVER indicator lights up . Both the LAMP/COVER • The electrical system breaks down the lamp and turn on the screen. Frequency is out of the projector. in 1 min. • Internal temperature is unusually high. Troubleshooting 41 GB c Wait for 90 seconds to XGA (VPL-CX5)...
... TEMP/FAN indicator • The fan is detached. Message Meaning and Remedy High temp.! c Check to "Component." c Replace the lamp. c Replace with qualified Sony personnel. c Attach the cover securely (see page 33). flashes. c Input a signal that is within the range of ... LAMP/COVER indicator lights up . Both the LAMP/COVER • The electrical system breaks down the lamp and turn on the screen. Frequency is out of the projector. in 1 min. • Internal temperature is unusually high. Troubleshooting 41 GB c Wait for 90 seconds to XGA (VPL-CX5)...
Operating Instructions
Page 44
... Optional accessories Projector Lamp LMP-C150 (for replacement) (1) Operating Instructions (1) Quick Reference Card (1) Ferrite core (1) Memory Stick (1) (VPL-CX5 only) Design and specifications are subject to change without the projection parts) Mass Approx. 2.7 kg (5 lb 15 oz) Power requirements AC 100 to 240 V, 50/60 Hz Power consumption Max. 240 W (Standby mode: VPL-CS5: 5 W VPL-CX5: 7 W) Heat dissipation...
... Optional accessories Projector Lamp LMP-C150 (for replacement) (1) Operating Instructions (1) Quick Reference Card (1) Ferrite core (1) Memory Stick (1) (VPL-CX5 only) Design and specifications are subject to change without the projection parts) Mass Approx. 2.7 kg (5 lb 15 oz) Power requirements AC 100 to 240 V, 50/60 Hz Power consumption Max. 240 W (Standby mode: VPL-CS5: 5 W VPL-CX5: 7 W) Heat dissipation...
Operating Instructions
Page 48
... Hue 30 I Image Flip 34 INPUT A connector .......12 pin assignment 44 Input-A Signal Sel. .........33 Installation examples .....16 notes 7 unsuitable conditions .... 7 unsuitable installation .. 7 L Lamp Mode 34 Lamp replacement .......... 36 Lamp Timer 35 Language 33 selecting the menu language 21 Location and function of controls connector panel .......... 12 control panel 12 rear/right side/bottom...
... Hue 30 I Image Flip 34 INPUT A connector .......12 pin assignment 44 Input-A Signal Sel. .........33 Installation examples .....16 notes 7 unsuitable conditions .... 7 unsuitable installation .. 7 L Lamp Mode 34 Lamp replacement .......... 36 Lamp Timer 35 Language 33 selecting the menu language 21 Location and function of controls connector panel .......... 12 control panel 12 rear/right side/bottom...