Sony VPL-CX3 - XGA LCD Projector Support and Manuals
Get Help and Manuals for this Sony item
View All Support Options Below
Free Sony VPL-CX3 manuals!
Problems with Sony VPL-CX3?
Ask a Question
Free Sony VPL-CX3 manuals!
Problems with Sony VPL-CX3?
Ask a Question
Popular Sony VPL-CX3 Manual Pages
Operating Instructions - Page 2
... more of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Address: 680 Kinderkamack Road, NJ 07649 U.S.A. Myers, Florida 33913 Telephone No.: 800-686-7669
The number below is intended to alert the user to the presence of Conformity
Trade Name: SONY Model No.: VPL-CX3 Responsible Party: Sony Electronics Inc. This symbol is for...
Operating Instructions - Page 5
... 11 Remote Commander 12
Setting Up and Projecting
Installing the Projector 14 Connecting the Projector 15
Connecting with a Computer ......15 Connecting with a VCR or 15k
RGB/Component Equipment 17 Selecting the Menu Language ..........19 Projecting 21 Effective Tools for Your Presentation 24
Maintenance
Maintenance 31 Replacing the Lamp 31 Cleaning the Air Filter 32
Troubleshooting 33...
Operating Instructions - Page 6
... lens while the lamp is on the LCD projector.
Do not use a damp cloth, detergent solution, or thinner.
• Clean the filter at the factory.
On LCD projector
• The LCD projector is equipped with ventilation...hard on the lens, use strong solvents, such as it is connected to install the projector in handy if you ever have it checked by qualified personnel before operating it ...
Operating Instructions - Page 7
...lamp allows high brightness (light output 900 ANSI lumen) and excellent uniformity on a NTSC4.43 system VCR.
• Windows is a registered trademark of Microsoft Corporation in the Memory Stick.
You can communicate data between the
Memory Stick attached to -use the supplied Remote Commander as VGA, SVGA, XGA... Remote Commander. Quiet operation
Because the projector uses Sony's...
Operating Instructions - Page 8
...90 seconds after the power is set to open the front cover.
2 OPEN button
3 Lamp cover (bottom)
4 Front remote control detector (SIRCS receiver)
5 Indicators
• LAMP/COVER: Lights up or flashes ...mode, any key is turned on the projector with the I / 1 key. - Lights up when temperature inside the projector becomes unusually high. - Flashes when the lamp cover or air filter cover is in ...
Operating Instructions - Page 9
...remote control detector (SIRCS receiver) How to use the adjuster" on page 10. Note Do not tilt the projector out of the range of the projector.
qa Adjuster adjustment buttons For details,see "Connector Panel" on the top panel of the adjuster setting...)
9 Focus lever Adjusts the picture focus. For details on the LAMP/COVER and the TEMP/FAN indicators, see "Control Panel" on pages 34...
Operating Instructions - Page 11
7 Arrow keys (M/m/
Operating Instructions - Page 15
... equipment before making connections, be sure to do the following procedures. 1 Connect the projector to the computer's instruction manual. However, we
recommend that are not fully inserted often generate noise. plugs that you set the output mode of your computer to XGA mode for each connection. • Insert the cable plugs properly; Notes • The...
Operating Instructions - Page 17
... audio output
VCR
Connecting the Projector 17 GB To connect a VCR
Left side
Stereo audio connecting cable (not supplied)
Video cable (not supplied)
to video output
S-Video cable (not supplied)
to S video output
to a VCR and 15k RGB/ component equipment. For more information, refer to the instruction manuals of the equipment you are...
Operating Instructions - Page 22
... the PICTURE CTRL menu on the screen.
See "VOLUME" in the INPUT SETTING menu when you adjust the picture manually. Key and joystick R CLICK (front) L CLICK (rear) Joystick
Function Right...Remote Commander
When you can cancel the adjustment by using the USB cable, you connect an IBM PC/AT compatible to the projector by pressing the APA key again while "ADJUSTING" appears on the projector...
Operating Instructions - Page 28
...LCD. The memory number and signal type of preset data for input signals (the preset memory). This projector has 20 types of user memories for the first time, a memory number is recalled from the INPUT A connector. See the chart on the suitable value for V increases, the picture moves up, and as the setting...and as the setting decreases, the picture moves down. Note
When XGA or SXGA ...
Operating Instructions - Page 31
... cord.
Maintenance 31 GB If you touch the lamp, you replace the lamp, wait for at least an hour for the lamp to cool.
Handle
4 Insert the new lamp all the way in place. Wait for at least an hour for the lamp to cool.
1 Place a protective sheet (cloth)
beneath the projector. Use LMP-C121 Projector Lamp as the replacement lamp.
Operating Instructions - Page 33
... the external monitor (see page 15). INPUT-A in the SET SETTING menu is incorrect. The picture from the connector and numbers of dot input from INPUT A • Setting for
strange. Maintenance
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem using the INPUT key (see page 21).
• The...
Operating Instructions - Page 35
... the SET SETTING menu is within the range of the frequency.
• The resolution setting of the output signal of the projector. c Set INPUT-A correctly (see page 15).
Both the LAMP/COVER ...replace the LAMP. • It is unusually high. and TEMP/FAN indicators c Consult with qualified Sony personnel. c Input a signal that is set to XGA (see page 29). Maintenance
Troubleshooting...
Operating Instructions - Page 42
... 27 INPUT-A 29 INSTALL SETTING
Menu 30 Installation examples .....14
notes 36 unsuitable conditions ..36 unsuitable installation .36
L
Lamp replacement .......... 31 LANGUAGE 29
selecting the menu language 19
Location and function of controls
connector panel .......... 11 control panel 10 front/side/bottom .......... 8 rear/left side 8 Remote Commander .. 12
M
Memory Stick slot ........ 11...
Sony VPL-CX3 Reviews
We have not received any reviews for Sony yet.