Sony RM-VL610B - Integrated Remote Commander Support and Manuals
Get Help and Manuals for this Sony item
View All Support Options Below
Free Sony RM-VL610B manuals!
Problems with Sony RM-VL610B?
Ask a Question
Free Sony RM-VL610B manuals!
Problems with Sony RM-VL610B?
Ask a Question
Popular Sony RM-VL610B Manual Pages
Operating Instructions - Page 1
4-117-851-11 (1)
Integrated Remote Commander
Operating Instructions
RM-VL610
©2008 Sony Corporation
Operating Instructions - Page 3
...free.) (page 33) You can remote control your non-Sony components by setting the type and code number of operating different AV components with this Commander, use it out of non-Audio Visual components such as Sony. Features
The RM-VL610 Remote Commander provides centralized control of all your AV components from a single remote commander and saves the trouble of each component (page 10...
Operating Instructions - Page 5
... code number is set, make the RM-VL610 "learn" the functions of your VCR's remote control until the SET indicator flashes.
5 Press and hold the H
(play ) signal of your video cassette recorder to the VCR H button of your component's remote control.
Press SET. Press and hold SET for
"learning" mode.
Example: To "teach" the H (play ) button of the RM-VL610
1 Place the RM-VL610 head...
Operating Instructions - Page 6
... Another Remote Control - Hold Function 34 Erasing all settings - Table of Contents
Getting Started
Installing the Batteries 8 When to replace the batteries 8
Location of Controls 9
Basic Operations
Setting the Code for Sony Components only 27
Executing a Series of Commands - To reset the Commander to its factory settings ..... 35
6 Setting component codes 10 Setting a component code...
Operating Instructions - Page 8
... batteries with new ones.
If the Commander does not operate properly, the batteries might be erased. Insert the batteries (negative end first) through the guide clamp within each compartment as shown above.
8 Be sure to match up to replace the batteries. Otherwise, your code number settings (page 10) and "learned" remote control signals (page 16) will last up...
Operating Instructions - Page 10
... code number 8011.
2 Press and while holding
SET, press MENU. If more than one code number is preset at the factory to operate Sony brand AV components (see "Assigning Other Components to any of the above Component Select buttons.
Basic Operations
Setting the Code for the desired component. Setting component codes
The Commander is listed, use the Commander with a factory-set...
Operating Instructions - Page 12
... the setup procedure using the Learning function (page 16), that "learned" signal will continue to indicate that you first set the TV and AMP codes before setting up when you press a function button, and turns off when you set up to work even after you release it .
If the Commander does not seem to indicate that the Commander is controlling...
Operating Instructions - Page 14
... Remote Commander
When you operate a non-Sony component, make sure you release it means that the setup is incomplete.
and POWER while setting the component code, all code numbers will be lost, and the setup procedure will be canceled. Notes • If you press any button other than CH +/- To set the component code first (page 10). To cancel setup, press SET...
Operating Instructions - Page 15
... that do not support the remote control of buttons for the TV or AMP buttons to send a signal to any other component, that signal will not work with the Learning function (page 16...the remote control signals with this setting (page 25). 2 Press any other component, that signal will be transmitted. • If you have assigned another component.
15
You can
change this Commander....
Operating Instructions - Page 16
...note of the Commander
1 Place the RM-VL610 head
to the VCR H (Play) button of the "learned" key functions. (It is "learned."
Learning Function
To operate components or functions which do not work even if you make a note on the back of Another Remote Control - Programming Signals of the supplied "Component code numbers.")
Notes • Some specific remote control signals
may not...
Operating Instructions - Page 18
... becomes very loud after pressing VOL + only once, noise may have interfered during the Learning procedure.)
If you set a component code after you set a component code. Programming Signals of each button on your component to the Commander.
To "teach" another component's remote control signal After positioning the two remote commanders as in Step 3. After data transfer is incomplete.
Operating Instructions - Page 24
... by following the steps of "Programming signals of another remote control -
Programming signals of another remote controlLearning Function" (page 16).
3 Program the power-off signal of the air-conditioner on signal and the power-off . Notes on the Commander.
To cancel erasing, press SET. Learning Function (continued)
2 While holding x pressed,
press the Component Select button you...
Operating Instructions - Page 37
... didn't come with the learning of the Commander.
The Component Select buttons flash by a remote commander. • You have set the component codes, then use the Learning function to an Audio System" (page 25).
• You have problems setting up the Commander as described in the supplied "Component Code Numbers."
• Some features may be controlled when you select components...
Operating Instructions - Page 38
... (page 16). You can insert an interval by Learning
Learning procedure. Troubleshooting (continued)
Symptom
Remedy
The SET indicator flashes • Learning has not succeeded. A Component Select
• The component codes cannot be
twice during setting.
codes again (page 10).
In this manual, if you still cannot get the Remote Commander to do not operate correctly because of...
Operating Instructions - Page 43
...(CLEAR)
q;
For example, to change the channel. To clear the setting. To fast-forward. To proceed to the receiver, the output switches ...desired program). To change to go into REC/ REVIEW mode during play . To switch the output of...Guide.
To operate "Flash +." To move the cursor upward. Channel up the title of the MENU display. To bring up Master Guide. Refer to its instruction
manual...
Sony RM-VL610B Reviews
We have not received any reviews for Sony yet.