Sony RM-VL700S - Integrated Remote Commander Support and Manuals
Get Help and Manuals for this Sony item
View All Support Options Below
Free Sony RM-VL700S manuals!
Problems with Sony RM-VL700S?
Ask a Question
Free Sony RM-VL700S manuals!
Problems with Sony RM-VL700S?
Ask a Question
Popular Sony RM-VL700S Manual Pages
Operating Instructions - Page 1
3-232-145-12 (1)
Integrated Remote Commander
Operating Instructions
RM-VL700
© 2001 Sony Corporation
Operating Instructions - Page 3
... as a control center for non-Sony components are its main features. This is useful when you can remote control your components by setting the type and code number of each component (page 8). The following are also preset This Commander is free). (See page 27.)
3 Remote control signals for your AV components from a single remote commander and saves the trouble of...
Operating Instructions - Page 4
... Started
Installing the Batteries 6 When to replace the batteries 6
Location of Controls 7
Basic Operations
Setting the Code for Sony Components only) ...26
Assigning Other Components to the Component Select Buttons 27 Copying the settings of another button .... 29
Using Other Functions
Locking the Controls - Learning Function .... 15 For accurate Learning 18 Programming remote control...
Operating Instructions - Page 6
...setting of the code numbers (page 8) and "learned" remote control signals (page 15) will last up the + and - indications on the batteries with new ones. When to replace the batteries
Batteries for a long period of the battery compartment with a cloth and replace...-andfirst through the guide clamp within each compartment as shown above.
Getting Started
Installing the Batteries
Slide ...
Operating Instructions - Page 8
... with a factory-set up a Philips' TV, you need to follow the procedures to freely set the correct codes for each component. For example, to operate Sony brand AV components (see the table below).
Setting component codes
The Commander is listed first. Component Select Button TV
VCR
CBL/SAT
Preset component(s) TV TV/VCR Combo VCR
Cable box
Factory setting Sony TV
Sony VHS VCR...
Operating Instructions - Page 9
... you press a button in the supplied "Component Code Numbers", or if you press SET while setting the component code, all other buttons turn off . The Component Select button turns off , it again. • If you don't input anything into the Commander within 20 seconds between each step, the setup procedure will be canceled.
3 Press the...
Operating Instructions - Page 10
... will continue to be working Try repeating the setup procedures using the Search function (page 11). It is controlling or muting the TV's volume. Note on buttons that the Commander is recommended that you first set the TV and AMP codes before setting up to indicate that have set the component code number. To use it . The Component button...
Operating Instructions - Page 12
... operate a non-Sony component, make sure you press any button other than CH+/- To cancel setup, press SET. If the Component Select button flashes five times before turning off, it .
12
Start over from the beginning.
Notes • If you release it means that the setup is incomplete. Setting a component code by following the instructions on page...
Operating Instructions - Page 13
.... • If you select an
audio component, the amplifier's
volume will be controlled (TV
lights up ). In this case, program the remote control signals with this
setting also (page 24).
to mute
the sound. When you select a
visual component, the TV's
volume will be controlled (AMP
lights up ), and when you used the Learning function
(page 15) to...
Operating Instructions - Page 15
...
RM-VL700
2 Press and hold SET for your component's remote control.
Example: To program the N (Play) signal of your video cassette recorder to the VCR N (Play) button of the Commander
1 Place the RM-VL700 head
to operate the functions of another remote control - The SET indicator lights up, and all Component Select buttons flash. It is recommended that you set a component code number...
Operating Instructions - Page 17
..." a signal If you have programmed any point during the Learning procedure.)
If you set a component code.
If the Commander does not seem to a single button on page 15, press the corresponding Component Select button, and then follow Steps 4 and 5 to perform Learning.
7 Press SET to other remote control, until both the SET indicator and the Component Select...
Operating Instructions - Page 33
... DVD, make sure you programmed the remote control signals with a remote commander, it probably isn't capable of an interactive signal exchange system remote control unit (supplied with some or all the codes for your component doesn't work, try all of the main unit may not be preset. other than TV or AMP.
• Set the component code correctly. If not...
Operating Instructions - Page 34
... work properly, call the Sony Customer Support Helpline at 1-800-822-2217.
34 All Component Select buttons flash twice.
• The Hold function is on. Replace them with new ones. See "For accurate Learning"
five times during the
(page 18) and try setting the component
during the
set has any remote control signals programmed by a constant interval when...
Operating Instructions - Page 39
... to turn muting off .
4 PIP (Favorite)
To switch the "FAVORITE" TV channel list programmed by a customer to ON/OFF
q sSLEEP (Exit/Clear)
To return to the TV screen from the html screen or the E-mail screen, etc.
q fOK
To command to its instruction manual for details.
39
q hRECALL
To toggle the current channel/the last...
Operating Instructions - Page 40
...27 copying settings 29 programming a signal 15 setting Power-On function 26 Copying settings of Component Select
buttons 29
E Erasing 31
F, G, H Factory setting 28, 31
I, J, K Input select 14
L Learning Function 15 Locking control of Commander 30
M MUTING button 10, 13, 18, 25, 30
N, O Number buttons 9, 14, 21, 27
P, Q, R, S Power-On function
setting 26 Preset components 8
T, U Troubleshooting 33...
Sony RM-VL700S Reviews
We have not received any reviews for Sony yet.