Sony RM-VL710 - Integrated Remote Commander Support and Manuals
Get Help and Manuals for this Sony item
View All Support Options Below
Free Sony RM-VL710 manuals!
Problems with Sony RM-VL710?
Ask a Question
Free Sony RM-VL710 manuals!
Problems with Sony RM-VL710?
Ask a Question
Popular Sony RM-VL710 Manual Pages
Operating Instructions - Page 3
... RM-VL710 Remote Commander provides centralized control of all your AV components from a single remote commander and saves the trouble of each component (page 8). You can remote control your Sony AV components. Centralized control of Sony AV components with the non-preset components.) (page 14) In addition, the Commander can "learn " the remote control signals needed to the TV Component...
Operating Instructions - Page 4
...by the Search function 11 Operating Your Components with the Remote Commander 12
To control the volume 13 Programming signals of another button .... 31
Using Other Functions
Locking the Controls - Setting component codes 8 Setting a component code 8 Checking if the code number works 10
Setting a component code by pressing that Component Select button (for non-Sony Preset Audio and Visual...
Operating Instructions - Page 6
... months.
If the Commander does not operate properly, the batteries might be erased. Notes on the battery compartment. Insert the batteries negative-andfirst through the guide clamp within each compartment as shown above. Be sure to match up to replace the
batteries
Batteries for a long period of the code numbers (page 8) and "learned" remote control signals (page 14...
Operating Instructions - Page 10
... the Commander is controlling or muting the TV's volume. Note on a button using the Learning function (page 14), that have already "learned" remote control signals If another signal has already been programmed on the VOL+/- TV
When you operate an audio component, the AMP button lights up when you press a function button, and turns off when you set the component code number...
Operating Instructions - Page 13
... ), and when
you used the Learning function (page 14) to program the VOL +/- Note, however, that components and functions that do not support the remote control of the TV or amplifier when you select that signal will be different for each component. to mute
the sound. In this case, program the remote control signals with this setting also (page 23).
Press...
Operating Instructions - Page 14
... you set a component code number, use the following Learning procedure to "teach" any of the programmable buttons or the Commander to operate the functions of another remote control - SET
POWER
TV VCR CBL DVD AMP
123
4 56
7 89
0 ENT
2,7 4 3
4
Example: To program the N (Play) signal of your video cassette recorder to the VCR N (Play) button of the Commander
1 Place the RM-VL710 head...
Operating Instructions - Page 16
... will work even after you set a component code after pressing VOL + only once, noise may have interfered during the process, Learning mode ends. • If you have programmed any signal on a button by the Learning function, that "learning" is complete, the Commander returns to other remote control, until both the SET indicator and the Component Select button lights up again. Repeat...
Operating Instructions - Page 17
... than the TV or AMP, that component. •If you used the Learning
function to place the Commander out of the reach of the Commander. If Learning does not work, try changing the positions of the two remote control units.
• When you used the Learning function to program the VOL +/ - other components, the "learned" signal will not reach the main...
Operating Instructions - Page 18
... Select buttons light. Either "teach" to 2 (page
14). You can release the Component Select button.
SET
TV VCR CBL DVD AMP
If another remote control - Both the SET indicator and the selected Component Select button flash (Learning function standby). Programming signals of another signal has already been "learned" by pressing DVD. (For this operation, an amplifier should first be...
Operating Instructions - Page 19
... Step 3 within 10 seconds after Step 2, the Learning procedure returns to other remote control, until the SET indicator lights and all the Component Select buttons flash again. Repeat from Step 2 while the Component Select button lights. 3 Press and hold the button
on the other buttons.
5 Press SET to finish
"learning."
To cancel "learning," press SET. Continued
19
Repeat Steps 2 and...
Operating Instructions - Page 20
...clear it first and perform Learning again. SET
SET
VCR
during data erasing
VCR
data erasing complete
Note Be sure to press the button you release the Component Select button, the Commander changes to Learning mode.
3 Press SET to erase.
+
When erasing of another remote control -
Programming signals of "learned" function is completed, the selected Component Select button light turns off...
Operating Instructions - Page 27
...
POWER
AMP
1
POWER
You can program up to that has been programmed with a series of commands of a "learned" button" on page 20. • If you change the component code number (page 8) or program a new signal by mistake, start again from Step 1. • If you try to program more than 16 steps, the System Control setting mode ends, and the 16 steps...
Operating Instructions - Page 30
...page 25) has been programmed.
For the example above in the step 2, you can program a Control Program
function (Component Macro) for over more than 20 seconds, the setting mode ends and the series of commands will not work until you do not use the original component
setting, set the component code number again (page 8). • If you set the entire program from the beginning.
Operating Instructions - Page 35
... the desired component is not listed in the supplied "Component Code Numbers".
• Some features may not be controlled when you 've set the component codes, then use the Learning function to program the remote control signals for the component (page 14).
• The component may interfere with new ones.
• Set the component code correctly. In case of the Commander.
Symptom...
Operating Instructions - Page 36
...five times "Component Code Numbers" and try setting the component
during the
(page 17) and try
setting again. See "For accurate Learning"
five times during setting.
function (page 14). If the problem persists, position the programmed components closer together.
• If the remote control receivers of the components do this manual, if you still cannot get the Remote Commander to...
Sony RM-VL710 Reviews
We have not received any reviews for Sony yet.