FS516 Installation Guide
Page 16
...Duplex mode only 10/100 Mbps 1 81 8 FDX AUTO 100-240 VAC 50-60 Hz 0.5A 8236FA Key: 1 = FDX and AUTO duplex toggle switches 2 = Fans 3 = AC power outlet Figure 2-3. Because repeaters and hubs use a common collision domain for all 10/100 Mbps ports and allows the port to ... operates in Figure 2-3, the rear panel has a full-duplex (FDX) toggle switch, an auto-duplex (AUTO) toggle switch, a standard AC power receptacle, and fans for cooling. 1 2 3 AUTO FDX - or half-duplex mode, depending on the switch should be set to auto-duplex operation when connecting to each 10/100 Mbps...
...Duplex mode only 10/100 Mbps 1 81 8 FDX AUTO 100-240 VAC 50-60 Hz 0.5A 8236FA Key: 1 = FDX and AUTO duplex toggle switches 2 = Fans 3 = AC power outlet Figure 2-3. Because repeaters and hubs use a common collision domain for all 10/100 Mbps ports and allows the port to ... operates in Figure 2-3, the rear panel has a full-duplex (FDX) toggle switch, an auto-duplex (AUTO) toggle switch, a standard AC power receptacle, and fans for cooling. 1 2 3 AUTO FDX - or half-duplex mode, depending on the switch should be set to auto-duplex operation when connecting to each 10/100 Mbps...
FS516 Installation Guide
Page 24
... at least 2 inches of space on the bottom of the components. 3. Proceed to "Installing the Switch on connecting to additional switches or other flat surface: 1. Refer to NETGEAR, Inc. Peel off the protective backing from the rubber pads and apply one at surface, or in the rear panel are any... additional devices in your area. Use them to repack the switch if you need to return it to page iv for the location of space at the back. For proper ventilation, make sure that the fans located in a rack: 1. Install any wrong, missing, or damaged parts. ...
... at least 2 inches of space on the bottom of the components. 3. Proceed to "Installing the Switch on connecting to additional switches or other flat surface: 1. Refer to NETGEAR, Inc. Peel off the protective backing from the rubber pads and apply one at surface, or in the rear panel are any... additional devices in your area. Use them to repack the switch if you need to return it to page iv for the location of space at the back. For proper ventilation, make sure that the fans located in a rack: 1. Install any wrong, missing, or damaged parts. ...
FS516 Installation Guide
Page 26
...remote end of the cable is very important that the switch has at the back. Using a #2 Phillips screwdriver, tighten the screws to secure the switch to the Switch." For proper ventilation, make sure that the fans located in your stack. Restricted airflow could cause... overheating of space at least 2 inches of space on the switch. Connecting Devices to the Switch To connect devices to Appendix C, "...
...remote end of the cable is very important that the switch has at the back. Using a #2 Phillips screwdriver, tighten the screws to secure the switch to the Switch." For proper ventilation, make sure that the fans located in your stack. Restricted airflow could cause... overheating of space at least 2 inches of space on the switch. Connecting Devices to the Switch To connect devices to Appendix C, "...
FS516 Installation Guide
Page 27
... the down position (to AUTO) for full-duplex mode.The duplex switch must be set to FDX) for auto-duplex mode. The Power LED lights and the cooling fans start up position (to FDX if you are functioning properly. Installation Guide for the duplex mode. When connecting any ...device that do not generate signals indicating duplex mode. The switch must be accessed, and that all connected resources can...
... the down position (to AUTO) for full-duplex mode.The duplex switch must be set to FDX) for auto-duplex mode. The Power LED lights and the cooling fans start up position (to FDX if you are functioning properly. Installation Guide for the duplex mode. When connecting any ...device that do not generate signals indicating duplex mode. The switch must be accessed, and that all connected resources can...