Netgear GS748TPS - ProSafe Switch - Stackable Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear GS748TPS manuals!
Problems with Netgear GS748TPS?
Ask a Question
Free Netgear GS748TPS manuals!
Problems with Netgear GS748TPS?
Ask a Question
Popular Netgear GS748TPS Manual Pages
GS7xxTPS Hardware manual - Page 13
... the key features of the NETGEAR Smart Switch. • On the GS700TPS Smart Switch device there are 48 RJ-45 ports 10/100/1000M auto sensing
Gigabit Ethernet switching ports, four of which are Combo ports.
With full-duplex enabled, the switch port connected to a file server.
Introduction
1-3
v1.0, April 2009 GS700TPS Smart Switch
The NETGEAR Smart Switch can be used as a desktop...
GS7xxTPS Hardware manual - Page 15
...'s low-level drivers, thorough the Distributed Switching application part that configures and manages all other unit member of the stack is designated as follows:
• 15.4W for 12 ports • 8W for 24 ports for a total of limited available power. • Supports the 48-Port PoE functions as slave stack members, and assigned a unique Unit ID. In particular, firmware can become...
GS7xxTPS Hardware manual - Page 25
... mask 255.255.255.0. The default IP address is a default IP address already configured on the
back of the switch. 2. You can turn off power to the switch. After powering up , check that the power cable is plugged in correctly and that is functioning correctly. For more information about managing the switch, see the Software Manual on the switch's front panel is green.
The...
GS7xxTPS Hardware manual - Page 27
...
This chapter describes the NETGEAR Smart Switch hardware features. Figure 3-1 illustrates the NETGEAR GS724TPS Smart Switch front panel
Figure 3-1
The front panel contains the following: • 24 RJ-45 connectors for 10/100/1000Mbps auto sensing Gigabit Ethernet switching ports. • Four SFP slots for more than 5 seconds. • One LED Mode Push Button to the factory defaults.
GS7xxTPS Hardware manual - Page 28
Figure 3-2
The front panel contains the following: • 48 RJ-45 connectors for 10/100/1000Mbps auto sensing Gigabit Ethernet switching ports. • Four SFP slots for more than 5 seconds. • One LED Mode Push Button to the factory defaults. Back Panel
Figure 3-3 illustrates the NETGEAR GS700TPS Smart Switch back panel:
Figure 3-3 3-2
v1.0, April 2009
Physical Description Every ...
GS7xxTPS Hardware manual - Page 30
No 10/100/1000Mbps link is established on the port.
• Flashing Green - Packet transmission or reception is occurring on PoE power circuit. • PoE power demand exceeds power
available. • PoE current exceeds PD's
Classification. • Out of proper voltage band (44-57
VDC).
• Off -
One LED/Port
24/48-10/100/1000 Ports PoE Mode - Packet ...
GS7xxTPS Hardware manual - Page 32
...attaching devices, all RJ-45 ports support Auto Uplink. When inserting a cable into the switch's RJ-45 port, the switch automatically:
• Senses whether the cable is backwards compatible with an RJ-45 port.
To simplify the procedure for setting uplink connections, while eliminating concern about whether to the RJ-45 ports with minimum stacking bandwidth of connection can be used...
GS7xxTPS Quick Install Guide - Page 1
... the online Software User's Manual is on the same subnet as
the switch. Use category 5 (Cat5) unshielded twisted-pair (UTP) cable terminated with an Ethernet adapter and a CD ROM drive. Power on a PC
1. The Installation Wizard will guide you cannot configure your network. Next, Connect Your Smart Switch in the Correct Order
These instructions assume you are using static IP addressing in...
GS7xxTPS User Manual - Page 9
GS700TPS Smart Switch Software Administration Manual Factory Default ...8-2
Upload ...8-3 Upload ...8-3
Download ...8-5 Download ...8-5
File Management ...8-6 Active Image ...8-6
Troubleshooting ...8-7 Diagnostics ...8-7
Chapter 9 Online Help
Online Help ...9-1 Support ...9-1 User Guide ...9-2 Appendix A Default Settings Index
ix v1.0, June 2009
GS7xxTPS User Manual - Page 19
... with Switch Management
1-6
v1.0, June 2009 A screen similar to disable DHCP. 8. The default IP address is 192.168.0.239 and the default subnet mask is 255.255.255.0.
If you
want different values, enter the switch IP address, gateway IP address and subnet mask. 9. GS700TPS Smart Switch Software Administration Manual
6.
Select Disable to that your password and click Set. Please...
GS7xxTPS User Manual - Page 27
...DELETE GO REFRESH TAGGED PORT MEMBERS TEST UNTAGGED PORT MEMBERS
Displays current members of a VLAN. Refreshes the screen with configuration information relating to access and use these functions, see Chapter 9, "Online Help". Displays tagged port members of a LAG. Tests copper cables.
Introduction to informational services including NETGEAR online support and an online user guide in the...
GS7xxTPS User Manual - Page 39
... system time: 1. If you selected Static IP Address, enter the IP Address, Subnet Mask and Gateway address. 4. Deletes the default gateway IP address.
• Management VLAN ID - The Time Configuration
screen displays:
Figure 3-3
Managing System Settings
3-5
v1.0, June 2009 GS700TPS Smart Switch Software Administration Manual
• Gateway - Select an existing VLAN to be defined as the...
GS7xxTPS User Manual - Page 85
...MED network policies, which include the application, VLAN ID, VLAN type, user priority and DSCP value. Select the Management IP Address from the interface.
- Voice VLANs • Provides Emergency Call Service (E-911) via IP Phone location information. • Provides troubleshooting information. LLDP-MED sends network managers alerts for : - Port speed and duplex mode conflicts - Click System...
GS7xxTPS User Manual - Page 161
... WRR - Bandwidth After packets are set the queue settings: 1.
Configuring QoS
5-5
v1.0, ...update the device. Check or uncheck the Restore Defaults box in the interface entry row. 5. Indicates the maximum number of data bits transmitted within a
specific time interval. • Committed Information Rate - Click QoS > CoS > Basic > Queue. GS700TPS Smart Switch Software Administration Manual...
GS7xxTPS User Manual - Page 234
..., and the type of cable error that is active after the specific unit is reset. - See "Reset" for the active image setting to a port. Click APPLY to be tested. Cable testing provides information about where errors occurred in the down state, with the exception of a copper cable attached to
take effect. Select the image file to update the device. Image 1 - Image...
Netgear GS748TPS Reviews
We have not received any reviews for Netgear yet.