Kenwood KAC-X522 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood KAC-X522 manuals!
Problems with Kenwood KAC-X522?
Ask a Question
Free Kenwood KAC-X522 manuals!
Problems with Kenwood KAC-X522?
Ask a Question
Popular Kenwood KAC-X522 Manual Pages
Instruction Manual - Page 1
... instruction manual. Model KAC-X522 Serial number US Residence Only
Register Online
Register your Kenwood dealer for information or service on the warranty card, and in the spaces designated on the product. Familiarity with installation and operation procedures will help you call upon your Kenwood product at www.kenwoodusa.com
© B64-3394-00/00 (KV) For your new power amplifier. KAC...
Instruction Manual - Page 2
... should be connected simultaneously. Cleaning the unit If the front panel gets dirty, turn the power on if the ground wire is a Protection function installed in the instruction manual. Available Control Units: A Kenwood's LX-Bus supporting Center Unit released in the Operation Manual of the speakers that are expressly approved in the unit to be connected should
be...
Instruction Manual - Page 3
... of settings and connections possible according to applications, read the instruction manual well to prevent short circuits. 2. Do not mount the unit in
which allows heat to decrease the internal temperature. English 3 Connect the power wire, power control wire and grounding wire following
this unit in the vehicle, check that gets hit by hot air)
• Do not install...
Instruction Manual - Page 4
... and check connections.
• Be sure to turn the power off before changing the setting of any switch.
• If the fuse blows, check wires for shorts, then replace the fuse with one of the Master amplifier to the Center Unit.
• The LX AMP and the sensor unit cannot be connected simultaneously. "7"
ID NUMBER
23...
Instruction Manual - Page 5
... switch allows to apply high-pass or low-pass filtering to use the unit as the Master amplifier. Set to this terminal.
7 ID NUMBER switch Sets an amp identification number (ID) to be used as a high-power monaural amplifier. (The input right signal is turned On. Otherwise malfunction may result.
6 RCA cable ground lead terminal When...
Instruction Manual - Page 6
... more seconds during ID number display ("AMP").
Indicates the current consumption (A).
Default
Resets all values you have set to cancel the Demonstration mode.
6 English Then, you can recall the value when message "LOAD" is displayed and you can register the values you have set with the Amplifier Control. The setup items are displayed approximately 1 second...
Instruction Manual - Page 7
... and their values are selecting an item with the Amp Control, an error status of the amplifier is in contact with the Center Unit.
Control an Amp from Center Unit
You can set items.
3 Set an ID number of Amp to operate
Set an amp's ID number on the Operation Manual of the Center Unit.
"CURR"
Indicates the current consumption...
Instruction Manual - Page 8
...Lch)
¡
OFF
LPF
OFF
OFF
STEREO
FILTER AMP CONT
ISF
OPERATION
HPF
ON
ON
MONO(Lch)
OFF
™ LPF
OFF
OFF
STEREO
■ High-power 2-channel subwoofer system
¡
L
L
L
...R
(μF)
fc=Cut of Frequency (Hz) R=Speaker Impedance (Ω)
Example: When it is required to set a crossover frequency of 120 Hz using a coil and capacitor...in a drop of 6dB/oct. Failure to...
Instruction Manual - Page 9
...may be set improperly. • The AMP CONT has been turned "OFF". • The filtered band has been controlled by the Amplifier Control.
• The AMP Control of the Center Unit is being used for possible problems.
PROBLEM No sound. (No sound from the Center Unit.
Specifications
Specifications subject to Noise Ratio (Bypass)...82 dBA (W/4 Ω)
English 9 Troubleshooting Guide
What...
Kenwood KAC-X522 Reviews
We have not received any reviews for Kenwood yet.