Honeywell 5800PIR-RES Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell 5800PIR-RES manuals!
Problems with Honeywell 5800PIR-RES?
Ask a Question
Free Honeywell 5800PIR-RES manuals!
Problems with Honeywell 5800PIR-RES?
Ask a Question
Most Recent Honeywell 5800PIR-RES Questions
Low Battery Alarm Stays On
(Posted by taimli022 1 year ago)
Sensors Do Not Detect Movement
My sensors do not detect movement unless I wave my hands right in front of them, or cover them with ...
My sensors do not detect movement unless I wave my hands right in front of them, or cover them with ...
(Posted by uebelhartthomas 5 years ago)
Honeywell 5800PIR-RES Videos
How to Perform a Walk Test with your Honeywell 5800PIR-RES Wireless Motion Detector
Duration: 3:07
Total Views: 8,978
Duration: 3:07
Total Views: 8,978
Get The Best HONEYWELL INTRUSION 5800PIR-RES WIRLESS
Duration: :52
Total Views: 358
Duration: :52
Total Views: 358
Honeywell 5800PIR-RES: DIY Installation of Wireless Infra-red Motion Detector
Duration: 8:13
Total Views: 7,169
Duration: 8:13
Total Views: 7,169
Honeywell 5800PIR Wireless Motion Detector Programming Vista 20p
Duration: 4:01
Total Views: 1,501
Duration: 4:01
Total Views: 1,501
Popular Honeywell 5800PIR-RES Manual Pages
Installation Instructions - Page 1
... outdoor PIR motion sensor. The major features are highlighted below:
ƒ Immunity to bright light disturbances from center up to reduce false alarms.
ƒ Tamper detection.
ƒ Selectable detector range and angle.
ƒ Battery saving circuit allows for normal operation. Installation Instructions
GENERAL INFORMATION
The Honeywell 5800PIR-OD Wireless Outdoor Motion Sensor...
Installation Instructions - Page 2
... to the Back Box.
2. Observe the proper polarity and
replace the batteries. Perform a Walk Test. 6.
UP
4. Perform a Walk Test.
7. Program the control panel. Use a pole with four self tapping
M3 x 14 screws.
4. Perform Settings &
Adjustments.
6. Then, remove 4 screws that secure the Detector to the pole. Secure the Detector to reveal the screw holes. You may have to move...
Installation Instructions - Page 3
... to 7ft) back from traffic.
Only the UPPER beam is blocked, detection is made . Adjust to the desired position. The lower detection area can be adjusted by the length of the motion sensor will not detect it to activate the sensor. Detection Length
Detection Length
Detection Length
UPPER and LOWER beams are blocked, detection is...
Installation Instructions - Page 4
... 2 or 4).
Pulse Count of 2 = detection can be shortened when using this setting.
2. IF NECESSARY, CONFIGURE DETECTION MASKING
1. Replace the Lens by aligning the 4 cutouts
on the next page. Set the Sensitivity Select Switch to the 4 projections inside the lens to prevent false detections. Set switch 1 to enable the Walk Test,
then perform the walk test on the lens to the desired...
Installation Instructions - Page 5
...1 to issue a false alarm by walking, either use in the control panel.
A heat source beyond the detection area may increase when there is set the Battery Saving Timer to reduce false detections. Examples include puddles, wet surfaces, very smooth asphalt or concrete surfaces.
ƒ If this causes a problem, adjust the detection length to the control panel's instructions for false or...
Installation Instructions - Page 6
...Check for correct battery installation, or replace dead batteries. Replace unit. Replace batteries. Set Detection Length to the source of light.
Alarms when no one is set correctly.
REMEDY
Check for cracks in the housing that would allow water infiltration. Perform a Settings & Adjustments procedure. No detection occasionally, or poor detection.
Sensor is not set too low...
Installation Instructions - Page 7
UP
Sensor (Do not touch)
Cover
LED Indicator
DIP Switch
Sensitivity Select
Switch
Detection Length
Ajustment Switch
Transmitter
Lens Holder
Lens
Cover
Captive Lock Screw M3 x 10
Masking Strip (Use as required)
- 7 - COMPONENT IDENTIFICATION DIAGRAM
Pole Bracket
Back Box
Use four M4x30 screws if mounting to pole brackets, or two M4x20 screws if mounting to wall.
Installation Instructions - Page 8
... device complies with Part 15 of the FCC Rules, and RSS210 of IC. DOCUMENTATION AND ONLINE SUPPORT For the latest documentation and online support information, please go to:
http://www.security.honeywell.com/hsc/resources/MyWebTech/
WARRANTY For the latest warranty information, please go to operate the equipment.
INFORMATION TO USER Unauthorized changes or modifications...
Honeywell 5800PIR-RES Reviews
We have not received any reviews for Honeywell yet.