User Manual
Page 26
...correct driver to use IDE3 and IDE4, please use it in unity with the Pin1. SATA0_SB / SATA1_SB 1 7 SATA0_SII / SATA1_SII 7 1 Pin No. 1 2 3 4 5 6 7 Definition GND TXP TXN GND RXN RXP GND These SATA connectors support hot plug function. English 9) IDE3 / IDE4 (IDE3 / IDE4 Connector, RAID/ATA133...) The red stripe of the ribbon cable must be the same side with BIOS (either RAID or ATA133). GA-K8NSNXP Motherboard - 26 - If you wish to have proper operation. For details, please ...
...correct driver to use IDE3 and IDE4, please use it in unity with the Pin1. SATA0_SB / SATA1_SB 1 7 SATA0_SII / SATA1_SII 7 1 Pin No. 1 2 3 4 5 6 7 Definition GND TXP TXN GND RXN RXP GND These SATA connectors support hot plug function. English 9) IDE3 / IDE4 (IDE3 / IDE4 Connector, RAID/ATA133...) The red stripe of the ribbon cable must be the same side with BIOS (either RAID or ATA133). GA-K8NSNXP Motherboard - 26 - If you wish to have proper operation. For details, please ...
User Manual
Page 78
...] Navigate [KL] Select [ENTER] Popup GA-K8NSNXP Motherboard - 78 - IDE, SCSI, or SATA. 3) Enter the motherboard BIOS and locate RAID setup (Please refer to the section on Integrated Peripherals). 4) Enter RAID setup in the BIOS and select the RAID type (For instance, enter F10 to press... information, please visit our website at http:\\www.gigabyte.com.tw) Configuring the NVIDIA RAID BIOS The NVRAID BIOS setup lets you choose the RAID array type and which hard drives you to select Silicon Image). 5) Complete driver installation. 6) Complete RAID utility installation. Press F10.
...] Navigate [KL] Select [ENTER] Popup GA-K8NSNXP Motherboard - 78 - IDE, SCSI, or SATA. 3) Enter the motherboard BIOS and locate RAID setup (Please refer to the section on Integrated Peripherals). 4) Enter RAID setup in the BIOS and select the RAID type (For instance, enter F10 to press... information, please visit our website at http:\\www.gigabyte.com.tw) Configuring the NVIDIA RAID BIOS The NVRAID BIOS setup lets you choose the RAID array type and which hard drives you to select Silicon Image). 5) Complete driver installation. 6) Complete RAID utility installation. Press F10.
User Manual
Page 80
..., such as Striping Block used as boot device if you want to boot operating system from the RAID BIOS, the next step is to configure and load drivers under Windows. Array 2 : NVIDIA MIRROR 111.79G - RAID Mode: Mirroring Striping Width : 1 Striping Block 32K Adapt Channel M/S 1 0 1 1 Master Master Index 0 1 Disk Model...Array Detail - The Array Detail screen appears. Press Enter again to go back to the previous screen and then press Ctrl + X to exit the RAID setup. English Press Y if you want to mark this disk as bootable. Array List - GA-K8NSNXP Motherboard - 80 -
..., such as Striping Block used as boot device if you want to boot operating system from the RAID BIOS, the next step is to configure and load drivers under Windows. Array 2 : NVIDIA MIRROR 111.79G - RAID Mode: Mirroring Striping Width : 1 Striping Block 32K Adapt Channel M/S 1 0 1 1 Master Master Index 0 1 Disk Model...Array Detail - The Array Detail screen appears. Press Enter again to go back to the previous screen and then press Ctrl + X to exit the RAID setup. English Press Y if you want to mark this disk as bootable. Array List - GA-K8NSNXP Motherboard - 80 -
User Manual
Page 81
... be listed on -screen instructions to complete installation. (Each time you complete the steps, boot from the Windows CD to install the RAID drivers. Follow on the screen (Refer to Fig.2), please select the proper chipset model. Technical Reference After you add a new hard drive ... DOS, please type in serial ATA controller, press F6 as Win2000 or XP boots up, then supply serial ATA controller driver by this driver file to a RAID array, the RAID driver will then automatically zip and transfer this floppy disk. Fig.1 Fig.2 (Note) Your system will have to be transferred ...
... be listed on -screen instructions to complete installation. (Each time you complete the steps, boot from the Windows CD to install the RAID drivers. Follow on the screen (Refer to Fig.2), please select the proper chipset model. Technical Reference After you add a new hard drive ... DOS, please type in serial ATA controller, press F6 as Win2000 or XP boots up, then supply serial ATA controller driver by this driver file to a RAID array, the RAID driver will then automatically zip and transfer this floppy disk. Fig.1 Fig.2 (Note) Your system will have to be transferred ...
User Manual
Page 84
... show a question mark "?" GA-K8NSNXP Motherboard - 84 - You have to resolve the USB device wake up S3 hang up issue in "Universal Serial Bus controller" under Windows XP operating system, please use Windows Service Pack. For USB2.0 driver support under "Device Manager". .../100/1000 Base LAN Driver For Marvell 10/100/1000 LAN chip driver. RealTek AC97 Codec Driver Realtek audio driver. Silicon Image RAID Driver Serial-ATA RAID driver for Silicon Image. GIGARAID IT8212 RAID Driver For ITE IT8212 RAID IDE controller. nVIDIA USB 2.0 Driver For nVIDIA USB 2.0 ...
... show a question mark "?" GA-K8NSNXP Motherboard - 84 - You have to resolve the USB device wake up S3 hang up issue in "Universal Serial Bus controller" under Windows XP operating system, please use Windows Service Pack. For USB2.0 driver support under "Device Manager". .../100/1000 Base LAN Driver For Marvell 10/100/1000 LAN chip driver. RealTek AC97 Codec Driver Realtek audio driver. Silicon Image RAID Driver Serial-ATA RAID driver for Silicon Image. GIGARAID IT8212 RAID Driver For ITE IT8212 RAID IDE controller. nVIDIA USB 2.0 Driver For nVIDIA USB 2.0 ...