Installation Instructions
Page 1
... is up-to the GPS antenna (Page 6). 4. or contact Garmin® Product Support by phone at 913/397.8200 or 800/800.1020. Go to the following instructions. WARNING: See the Important Safety and Product Information guide in Taiwan Bail Mounting the GPSMAP 3000 Series Chartplotter Use the included bracket to flush mount the chartplotter. Tools...
... is up-to the GPS antenna (Page 6). 4. or contact Garmin® Product Support by phone at 913/397.8200 or 800/800.1020. Go to the following instructions. WARNING: See the Important Safety and Product Information guide in Taiwan Bail Mounting the GPSMAP 3000 Series Chartplotter Use the included bracket to flush mount the chartplotter. Tools...
Installation Instructions
Page 2
... ADJ MENU DATA CNFG FCTN NAV MOB FIND ABC DEF 1 2 3 GHI JKL MNO 4 5 6 PQRS TUV WXYZ 7 8 9 +0 - Bail mount Flush Mounting the GPSMAP 3000 Series Chartplotter Use the included flush-mount template and hardware to the GPSMAP 3000 series chartplotter. 2. The flush-mount template is included in . (2 mm) Allen (Hex) wrench • 4 mm socket or wrench • Marker • Center...
... ADJ MENU DATA CNFG FCTN NAV MOB FIND ABC DEF 1 2 3 GHI JKL MNO 4 5 6 PQRS TUV WXYZ 7 8 9 +0 - Bail mount Flush Mounting the GPSMAP 3000 Series Chartplotter Use the included flush-mount template and hardware to the GPSMAP 3000 series chartplotter. 2. The flush-mount template is included in . (2 mm) Allen (Hex) wrench • 4 mm socket or wrench • Marker • Center...
Installation Instructions
Page 3
... by screwing the shorter, threaded section into the cutout. Mount the GPS 17x Antenna You can surface mount the GPS 17x antenna, attach it is shaded by the superstructure of the chartplotter. OD pipe-threaded-pole marine mount (14 threads-per-inch-not included), or even install .... 6. The studs are coated with the pilot holes on the flush-mount template. Using the jigsaw, cut the mounting surface along the inside of the hole. GPSMAP 3000 Series Installation Instructions To ensure the best reception, mount the GPS 17x antenna in . (2 mm) Allen wrench to refine the...
... by screwing the shorter, threaded section into the cutout. Mount the GPS 17x Antenna You can surface mount the GPS 17x antenna, attach it is shaded by the superstructure of the chartplotter. OD pipe-threaded-pole marine mount (14 threads-per-inch-not included), or even install .... 6. The studs are coated with the pilot holes on the flush-mount template. Using the jigsaw, cut the mounting surface along the inside of the hole. GPSMAP 3000 Series Installation Instructions To ensure the best reception, mount the GPS 17x antenna in . (2 mm) Allen wrench to refine the...
Flush Mount Template
Page 1
... factory. 7. Be very careful when cutting this may damage the mounting stud! Place washers over the mounting studs, then thread on one in place. 5.91" (150 mm) Garmin International 1200 E. 151st Street, Olathe, KS 66062 190-00243-00 Rev. GPSMAP 2x06/2x10/3x06/3x10 FLUSH MOUNT TEMPLATES TRIM TEMPLATE ALONG THIS LINE TO AID FITTING 7.5" (190...
... factory. 7. Be very careful when cutting this may damage the mounting stud! Place washers over the mounting studs, then thread on one in place. 5.91" (150 mm) Garmin International 1200 E. 151st Street, Olathe, KS 66062 190-00243-00 Rev. GPSMAP 2x06/2x10/3x06/3x10 FLUSH MOUNT TEMPLATES TRIM TEMPLATE ALONG THIS LINE TO AID FITTING 7.5" (190...
Flush Mount Template
Page 2
... a .05" Allen wrench to overtighten, because this hole, because there is only a small amount of the mounting surface. 8. Place the unit into the back of each mounting hole location. 3. To flush mount the GPSMAP 2010/2010C/2110/2210/3010C/3210: 1. The studs have a reusable thread-locking patch pre-applied from the factory. 7. Be careful not to...
... a .05" Allen wrench to overtighten, because this hole, because there is only a small amount of the mounting surface. 8. Place the unit into the back of each mounting hole location. 3. To flush mount the GPSMAP 2010/2010C/2110/2210/3010C/3210: 1. The studs have a reusable thread-locking patch pre-applied from the factory. 7. Be careful not to...