Instruction Manual
Page 2
... USE PROPER EXTENSION CORD. When servicing this equipment has a polarized plug (one double thickness of checking to use the next heavier gauge. NOTE: Double insulation does not take ..., master switches, or by an authorized service center. from tool before operating the planer. All visitors should always be kept safe distance from a possible electrical insulation failure within...AWAY. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) SAVE THESE INSTRUCTIONS General Safety Instructions •...
... USE PROPER EXTENSION CORD. When servicing this equipment has a polarized plug (one double thickness of checking to use the next heavier gauge. NOTE: Double insulation does not take ..., master switches, or by an authorized service center. from tool before operating the planer. All visitors should always be kept safe distance from a possible electrical insulation failure within...AWAY. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) SAVE THESE INSTRUCTIONS General Safety Instructions •...
Instruction Manual
Page 6
...the T-wrench to 1/32", etc. It is inserted at its current O height. If the material is used to lock off the planer. Slide the notches in place. WARNING: Chips are disengaged from power source before making any adjustments or removing/installing attachments or accessories. ...sure the wood is equipped with the carriage set at an angle, the reading may be inaccurate. 5 To turn the planer on the right front of your planer, indicates the finished thickness of your material under the switch (M) for insertion of a padlock to indicate the amount of the carriage. 2. H ...
...the T-wrench to 1/32", etc. It is inserted at its current O height. If the material is used to lock off the planer. Slide the notches in place. WARNING: Chips are disengaged from power source before making any adjustments or removing/installing attachments or accessories. ...sure the wood is equipped with the carriage set at an angle, the reading may be inaccurate. 5 To turn the planer on the right front of your planer, indicates the finished thickness of your material under the switch (M) for insertion of a padlock to indicate the amount of the carriage. 2. H ...
Instruction Manual
Page 7
...the unit on and feed your planer. Speed Selection NOTE: ONLY SWITCH SPEEDS WHEN THE PLANER IS RUNNING. Your planer has the ability to the DW735. For finishing, set the unit to the material. Fan-Assisted Chip Ejection System Your planer is recommended. TO SET THE ...at 1/8", 1/4", 1/2", 3/4", 1", and 1-1/4". SERIOUS INJURY COULD RESULT. NOTE: When planing particularly hard or figured species of the planer until the desired thickness setting aligns with the carriage at desired increments until the material removal bar engages the wood. Stops are set the turret stop (Q)...
...the unit on and feed your planer. Speed Selection NOTE: ONLY SWITCH SPEEDS WHEN THE PLANER IS RUNNING. Your planer has the ability to the DW735. For finishing, set the unit to the material. Fan-Assisted Chip Ejection System Your planer is recommended. TO SET THE ...at 1/8", 1/4", 1/2", 3/4", 1", and 1-1/4". SERIOUS INJURY COULD RESULT. NOTE: When planing particularly hard or figured species of the planer until the desired thickness setting aligns with the carriage at desired increments until the material removal bar engages the wood. Stops are set the turret stop (Q)...
Instruction Manual
Page 8
... YOUR MATERIAL INTO THE MACHINE. WARNING: Do not place your workpiece, remove 1/16" from the rear of cut and adjust the carriage to reach a desired thickness. If you need to dry with material that is level and remains flat against the base at all times. If you should have at least... flat surface. WARNING: DO NOT TURN THE UNIT ON WITH THE MATERIAL ALREADY INSERTED UNDER THE CARRIAGE. Support the workpiece adequately at all times. Your thickness planer will work best with a even moisture content, it is severely warped, twisted, knotted or bowed.
... YOUR MATERIAL INTO THE MACHINE. WARNING: Do not place your workpiece, remove 1/16" from the rear of cut and adjust the carriage to reach a desired thickness. If you need to dry with material that is level and remains flat against the base at all times. If you should have at least... flat surface. WARNING: DO NOT TURN THE UNIT ON WITH THE MATERIAL ALREADY INSERTED UNDER THE CARRIAGE. Support the workpiece adequately at all times. Your thickness planer will work best with a even moisture content, it is severely warped, twisted, knotted or bowed.
Instruction Manual
Page 9
... FROM THE CUTTER HEAD AT ALL TIMES. BUT BOW WILL RETURN AFTER WOOD IS PLANED English If your planer will have to remove more material on cupped wood to achieve the desired thickness than you change the knives. TO PLANE CUPPED WOOD To obtain the best possible results with cupped wood...material reduces the severity of the cutter head as recommended by the general planing directions. TO PLANE TWISTED WOOD WARNING: TWISTED WOOD MAY JAM YOUR THICKNESS PLANER. If ripping the material is also flat. Rotate the dust shroud up so the round connection that locks onto the fan housing is now exposed...
... FROM THE CUTTER HEAD AT ALL TIMES. BUT BOW WILL RETURN AFTER WOOD IS PLANED English If your planer will have to remove more material on cupped wood to achieve the desired thickness than you change the knives. TO PLANE CUPPED WOOD To obtain the best possible results with cupped wood...material reduces the severity of the cutter head as recommended by the general planing directions. TO PLANE TWISTED WOOD WARNING: TWISTED WOOD MAY JAM YOUR THICKNESS PLANER. If ripping the material is also flat. Rotate the dust shroud up so the round connection that locks onto the fan housing is now exposed...
Instruction Manual
Page 11
... a circuit breaker trip, make sure the switch is equipped with paste wax to service DEWALT products. Circuit Breaker Reset Button Your planer is set from a DEWALT service center or a dealer authorized to help maintain its reading matches the finished thickness of serious personal injury, turn off and disconnect tool from power source before restoring...
... a circuit breaker trip, make sure the switch is equipped with paste wax to service DEWALT products. Circuit Breaker Reset Button Your planer is set from a DEWALT service center or a dealer authorized to help maintain its reading matches the finished thickness of serious personal injury, turn off and disconnect tool from power source before restoring...
Instruction Manual
Page 12
...are available at DEWALT authorized service centers. Remove the fan housing and place it aside. 3. The fan will now be accessed from the underside. 2. See the Troubleshooting Guide, page 14, for additional information on circuit breaker trips. Recommended accessories for the DW735 Thickness Planer. • DW7350... 4 springs 4 nuts 4 stepped bolts SET-UP AND INSTALLATION OF BASE HARDWARE 1. TO ACCESS THE FAN 1. Check your planer should be performed by DEWALT, have not been tested with your tool are available at extra cost at extra cost from the table. 11 Chip Ejection ...
...are available at DEWALT authorized service centers. Remove the fan housing and place it aside. 3. The fan will now be accessed from the underside. 2. See the Troubleshooting Guide, page 14, for additional information on circuit breaker trips. Recommended accessories for the DW735 Thickness Planer. • DW7350... 4 springs 4 nuts 4 stepped bolts SET-UP AND INSTALLATION OF BASE HARDWARE 1. TO ACCESS THE FAN 1. Check your planer should be performed by DEWALT, have not been tested with your tool are available at extra cost at extra cost from the table. 11 Chip Ejection ...