Dewalt D28115N Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt D28115N manuals!
Problems with Dewalt D28115N?
Ask a Question
Free Dewalt D28115N manuals!
Problems with Dewalt D28115N?
Ask a Question
Popular Dewalt D28115N Manual Pages
Instruction Manual - Page 3
...the cord for outdoor use any way. Please read the instruction manual.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock... outlet. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). b) Do not operate power tools in explosive atmospheres...
Instruction Manual - Page 4
...collection facilities, ensure these instructions to a rotating part of dust collection can be repaired. c) Prevent unintentional starting...moving parts. The correct power tool will ensure that may result in the hands of... tool in a hazardous situation.
5) SERVICE a) Have your power tool serviced by poorly maintained power tools. Do ...repair person using only identical replacement parts.
Instruction Manual - Page 5
...grinder, sander, wire brush, polisher or cut-off tool.
The dust mask or respirator must properly fit the spindle of wheels, flanges, backing pads or any other accessory must be attached to follow all safety warnings, instructions, illustrations and specifications... Read all instructions listed below may ...install an undamaged accessory.
English
SAFETY INSTRUCTIONS... metal parts of ...
Instruction Manual - Page 8
...operate this tool for Grinders
WARNING: The grinding wheel or accessory may cause permanent injury to fingers, hands, and arms. Use ... moving parts and should always be used to work by the operating action of this manual is recommended for Cord Sets
Ampere...
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
6 An undersized cord will cause a ...
Instruction Manual - Page 10
...) F. Anti-Vibration Side Handle (not shown)
INTENDED USE
The D28065, D26065N, D28115, D28115N heavy-duty angle grinders have been designed for professional grinding at various work sites (i.e., construction sites). Supervision ...power source before installing and removing accessories, before adjusting or when making repairs. A. DO NOT use this tool. Lock On Button
(D28065, D28115 only) C....
Instruction Manual - Page 13
... above listed minimum wheel speed as shown on pages 9-11 of this manual. The tool may burst and cause injury. Some DEWALT models are included in ./lbs. (2.03 Nm) torque. Overtightening could cause screws to 18 in the accessory package.
11 Failure to have the tool serviced may have been designed for use with grinder accessories...
Instruction Manual - Page 14
...installing and removing accessories, before touching the work surface. Do not operate the grinder with the grinder...handle and body of the tool firmly to repair
or replace the guard. The
J
guard body should...listed minimum wheel speed as shown on the tool warning label. WARNING: Accessories must be tightened by hand.... Push the guard down .
12 CAUTION: Do not tighten the adjusting...
Instruction Manual - Page 15
... to ensure that the switch is retained to the grinder by an O-ring on the spindle. Depress and release...described above procedure to remove the wheel.
LOCK-ON BUTTON (D28065, D28115) (FIG. 5)
The lock-on spindle
(N) with D28065 G1,...Sanding Flap Discs
MOUNTING AND REMOVING HUBBED WHEELS
Hubbed wheels install directly on the spindle by hand.
3. Backing flange is off . Thread the wheel...
Instruction Manual - Page 16
...Remove the tool from holding the wheel. Type 1 guards are installing is 1/8" (3.17 mm) thick or less, place the threaded... thin wheel is being
used for more than 1/2" (12.7 mm) in the workpiece, do cut is begun ...to the work surface.
4. The
open - Changing
the angle will spin because the height of these wheels with the pilot...service
center. 1. Place wheel against the wheel.
4.
Instruction Manual - Page 17
...backing pad.
4. Allow the tool to work surface.
15 While depressing spindle lock, thread FIG. 12
clamp nut (H) on spindle, piloting the H
P
raised hub on the backing pad.
3.
SURFACE ... Tighten the clamp nut by hand. Sanding rate is available in the work surface.
2. Allow the tool to stop rotating before touching the tool to 10˚ angle between the tool and work surface...
Instruction Manual - Page 18
...5˚ to 10˚ angle between the edge of the
wire wheel or brush to prevent burning and swirling of grinder may result in a circular ...the work surface before turning the tool on the spindle by hand. 2. A Type 27 guard is greatest when the tool operates... use of flanges. CAUTION: Failure to reach full speed before setting it down . Remove the tool from accessory wheel or cup....
Instruction Manual - Page 19
...up .
Abrasive
cutting wheels for side pressures encountered with surface grinding. NOTE: All grinders that the arrows are available. MOUNTING CUTTING WHEELS CAUTION: Matching diameter backing flange and ...positioned between the spindle and K the operator to rotate the guard
by hand when the latch is installed. 2.
Close the guard latch to secure the
guard on the quick-change...
Instruction Manual - Page 20
...the angle of injury, only DEWALT ...service in these parts. Register online at high speed. These chemicals may cause wheel breakage.
4. never immerse any part of such accessories with your tool are available at high speed.
3. Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by DEWALT...
Instruction Manual - Page 21
...the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE DEWALT will repair, without charge, any defects due to products sold in Latin America, see country specific warranty information...DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE If you are missing, call 1-800-4-DEWALT...
Instruction Manual - Page 72
N234380 D28065, D28065N, D28115, D28115N Copyright © 2007, 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and ...
Dewalt D28115N Reviews
We have not received any reviews for Dewalt yet.