Dewalt DWE402 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWE402 manuals!
Problems with Dewalt DWE402?
Ask a Question
Free Dewalt DWE402 manuals!
Problems with Dewalt DWE402?
Ask a Question
Dewalt DWE402 Videos
DeWALT Small Angle Grinder DWE402
Duration: 5:55
Total Views: 933
Duration: 5:55
Total Views: 933
Ace Tool | Dewalt DWE402 4-1/2" (115mm) Small Angle Grinder
Duration: 1:12
Total Views: 34
Duration: 1:12
Total Views: 34
THE NEW DWE402 SMALL ANGLE GRINDER BY DEWALT
Duration: 1:12
Total Views: 5,074
Duration: 1:12
Total Views: 5,074
DeWalt 4-1/2 In. 11 Amp Angle Grinder Model #DEWALT-DWE402
Duration: 1:29
Total Views: 36
Duration: 1:29
Total Views: 36
Popular Dewalt DWE402 Manual Pages
Instruction Manual - Page 5
... of the flange. Depending on the power tool.
f) Do not use inspect the accessory such as a grinder, sander, wire brush, polisher or cut-off tool. Prolonged exposure to follow all safety warnings, instructions, illustrations and specifications provided with this test time.
Cutting accessory contacting a "live" wire may cause loss of the power tool "live" and could...
Instruction Manual - Page 6
... or against your body leaves it rough treatment. Causes and Operator Prevention
of the spinning accessory. r) When starting the tool with a person in a careful manner. Never start the tool with a new or replacement wheel, or a new or replacement wire brush installed, hold the tool in a well protected area and let it run the power tool...
Instruction Manual - Page 8
...
6
Tuck away or trim any interference of this product.
b) If the use of a guard is restarted in motion otherwise kickback may cause snagging, tearing of the polishing bonnet or its ... or snag on both sides of cut . Wire wheel or brush may expand in the workpiece. Supports must be worn by the brush even during ordinary operation.
Safety Warnings Specific for Sanding ...
Instruction Manual - Page 10
... injury could result. Type 27 Guard (4-1/2" / 115mm)
C. Side handle
FIG. 1 J
E J
8
DWE402, DWE402N, DWE402G
K
I
C
A
DWE4214
B
I . Paddle switch
G. Lock-off lever
J. Guard release lever
D. Slider switch (DWE4214)
H. Threaded locking flange
I
G
D
H F Spindle lock button
K. Spindle
(DWE402, DWE402G)
F. English
Minimum Gauge for Cord Sets
Volts
Total Length of...
Instruction Manual - Page 11
...strip. Accessory
ratings must have the tool serviced may cause
brush, motor and bearing failure.
3. These heavy-duty small angle grinders are ...guards, backing pads and flanges to
20 in presence of more than 10% will rotate 90° for at various work sites (i.e., construction sites). Threaded accessories must always be rated for cutting operations. DO NOT use this manual...
Instruction Manual - Page 12
... accessory guards not included with the slots (M) on the gear case.
3. A Type 1 guard must be used with conventional sanding discs. While holding the guard release lever open , push the guard down until the guard lugs engage and rotate them in the groove on the guard with the tool. MOUNTING, ADJUSTING AND REMOVING (TYPE 27) ONE-TOUCH™ GUARD (FIG. 3)
Your grinder...
Instruction Manual - Page 13
... the guard in a clockwise, single action motion. To remove the guard, follow steps 1-3 of these instructions in the clockwise direction. non-hubbed sanding flap disc
threaded locking flange
4. For easy adjustment, the guard can be rotated in reverse. This ensures that the guard is available at extra cost from your local dealer or authorized service center...
Instruction Manual - Page 14
...
PADDLE SWITCH (FIG. 1, 4)
DWE402, DWE402G
CAUTION: Before connecting the tool to a power source depress
and release the paddle switch (A) once [DWE402: without depressing
the lock-on ,...or
removing/installing attachments or
accessories. If the paddle switch is important to choose the correct guards and flanges to a power supply, be performed with the grinder accessories.
Guards and ...
Instruction Manual - Page 15
...Install the unthreaded backing flange FIG. 8
(G) on spindle (E) with included flanges.
FIG. 5
LOCK-ON BUTTON (FIG. 6)
B
DWE402, DWE402G... 9)
Depressed center Type 27 and Type 42 grinding wheels must...rear part of...guard per the instructions in this manual
for more information.
1. This
C
A
K
will result and attached accessory may spin off . Lift the tool from rotating when
installing...
Instruction Manual - Page 16
... surface, allowing the tool to 30° angle between the tool and work surface, allowing the tool to the reduction of the wheel is installed with the pilot on the spindle so that the... the locking flange from you.
4. In all edge grinding/cutting operations, the open side of a Type 1 guard.
1. NOTE: If the wheel spins after the threaded locking flange is new. Apply minimum pressure to...
Instruction Manual - Page 19
... Brushes and Wire Wheels
Wire cup brushes or wire wheels screw directly on the grinder spindle...installing attachments or accessories.
An accidental start-up and disposed of flanges. Material removal rate is required when using wire brushes and wheels. Plastic drop cloths should be taken when wire brushing paint as when sanding paint (refer to the tool, wheel or brush must not touch guard...
Instruction Manual - Page 20
... paddle switch to stop rotating before making any adjustments or removing or installing attachments or accessories. With the spindle facing the operator,
rotate the guard clockwise into one of the
alignment holes (O) on the gear case.
3. To remove the guard, follow steps 1-3 of grinder may be experienced. Diamond blades for concrete cutting can also be...
Instruction Manual - Page 21
... than those offered by
USING TYPE 1 OR TYPE 41 CUTTING WHEELS
DEWALT, have not been tested with this product, use of the tool into a liquid.
5.
Accessories
WARNING: Since accessories, other harsh chemicals for use edge grinding/cutting wheels for surface accessories with your local dealer or authorized service center. Never let any part of such
WARNING: Do not...
Instruction Manual - Page 22
...
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT authorized service center or other rights which vary in Latin America. This warranty does not cover part failure due to contact you obtain more efficient warranty service in case there is required under...
Instruction Manual - Page 72
N382909
DWE402, DWE402N, DWE402G, DWE4214 Copyright © 2014 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the array
of pyramids on the surface of lozenge-shaped humps on the handgrip; and the array of the tool. the kit box configuration; DEWALT Industrial Tool Co., 701 East Joppa...
Dewalt DWE402 Reviews
We have not received any reviews for Dewalt yet.