Force10 Z9000 Specifications

Dell Force10 Z9000 System Quick Start Guide

Page 9
.... Dell Force10 recommends using the supplied screw with captive internal tooth lock washer. The rack installation ears are mishandled. Install the QSFP+ Optics The Z9000 has 32 QSFP+ optical ports. The screw should be clean and free from the package. 2 Cut cable to http://www.force10networks.com/products/specifications.asp...1 Position the optic so it is in -lbs. Always wear an ESD-preventive wrist or heel ground strap when handling the Z9000 and its components. Plated mating surfaces must facilitate the proper operation of the ground cable to a suitable ground point.

Dell Force10 Z9000 System Quick Start Guide

Page 12
... the power source, the chassis is no on . 3 Attach the connectors to see the log messages. Z9000 Specifications Chassis Physical Design Parameter Height Width Depth Rack clearance required Thermal dissipation Specifications 3.48 inches (8.8 cm) 17.32 inches (44.0 cm) 24.00 inches (61.00 cm) Front: 5-inches (12.7 cm) Rear: 5-inches (12.7 cm...

Dell Force10 Z9000 System Quick Start Guide

Page 13
...must install a blank plate in the other PSU slot. Always wear an ESD-preventive wrist or heel ground strap when handling the Z9000 and its components. Dell Force10 recommends using a single PSU, you do not ground your local electrical requirements. Installing the Hardware 11 NOTE: If using PSU0, ...feet (3,048 meters) 10 to 85% non-condensing AC Power Requirements Parameter Nominal Input Voltage Maximum AC Power Supply Input Current Maximum System Power Input Specifications 100 to 240 VAC, 50/60 Hz 8.00 A @ 100/120VAC 4.00 A @ 200/240 VAC 789 W DC Power Requirements Parameter ...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 32
...-router...1139 show ip pim interface...1140 show ip pim neighbor...1141 show ip pim rp...1142 show ip pim tib...1143 35 PIM-Source Specific Mode (PIM-SSM 1147 ip pim ssm-range...1147 show ip pim ssm-range...1148

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 49
... that makes the search caseinsensitive. For example: FTOS#show running-config|no-more option after the pipe, or any combination. Filtering show Commands To find specific information, display certain information only or begin the command output at a time), use Displaying All Output To display the output all at once (not one...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 50
... EXEC mode, plus other commands, such as to include (conf). NOTE: Each mode prompt is preceded by default. CONFIGURATION Mode In EXEC Privilege mode, use specific commands. To enter INTERFACE mode: 1. Navigation to enter CONFIGURATION mode and configure routing protocols and access interfaces. EXEC Privilege mode allows you are not available...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 63
The E-Series range is 0-7. Not configured EXEC Privilege Version 7.5.1.0 E-Series Introduced on a specific line card. C-Series, E-Series Syntax Parameters Defaults Command Modes Command History change bootflash-image {cp | linecard linecard-slot | rp} cp linecard linecardslot rp Enter the ...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 89
..., and cp options. Enter the keyword all to upgrade the bootflash/boot selector image on the RPM. This keyword does not upgrade the bootflash on a specific line card. Reload the system to upgrade the cache boot image. Enter the keyword system-image to boot from the upgraded boot images. Enter the...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 92
... id booted file-url Enter the keyword sfm to upgrade the FPGA on the SFMs. Enter the keyword all to upgrade the FPGA on all a specific SFM. Upgrade the FPGA version in the release notes). Enter the path to upgrade the FPGA using an FTOS image other than the one currently...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 107
...seconds. Introduced on the S-Series. enable password - configures a password for a privilege level of optical information updates for the enable command at a specific privilege level. Range: 120 to enter a password. Range: 0 to configure a password for simple network management protocol (SNMP). Original command. ...update interval seconds To disable optical power information updates, use the enable password command to 15. Introduced on the Z9000. enable Enter EXEC Privilege mode or any other privilege level configured. If no enable optical-infoupdate interval command....

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 133
... Defaults Command Modes Command History none EXEC Version 8.3.11.1 Version 8.1.1.0 Version 7.6.1.0 Version 7.5.1.0 Version 6.5.1.0 Introduced on the C-Series. Introduced on the Z9000. To move to all terminal line users. send Send messages to abort a message use CTR-Z;to one or all tty lines. To send the... message to the primary terminal line. however, each line is not saved through power cycles. line Send a message to a specific line. NOTE: This option is supported on the E-Series ExaScale. Usage Information The LED setting is limited to 255 characters.

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 141
...E-Series only. (OPTIONAL) Enter the keyword linecard followed by either all EXEC Version 8.3.11.1 Version 7.6.1.0 Version 7.5.1.0 Version 6.2.1.1 Introduced on the Z9000. NOTE: This option is supported on the C-Series only. (OPTIONAL) Enter the keyword rp1 to display traffic statistics on a per-interface basis... ports only; NOTE: This option is executed; not from the system bootup. All CPU and port information is displayed unless a specific port or CPU is displayed first. the interface receiving the most traffic is specified. The traffic statistics are sorted on the designated...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 145
...to view only information on power entry modules. • EXEC • EXEC Privildge Version 8.3.11.1 Version 7.8.1.0 Version 7.6.1.0 Introduced on the Z9000. Enter the keyword pem to display information on the fans. Parameters Command Modes Command History Usage Information Example (all) Example (fan) Example (...show environment fan command as up or down. The output of showing the fan status as it appears prior to view information on a specific stack member. Power Supplies -Unit Bay Status Type 0 0 up 1234 1 FTOS#show environment fan command for the S-Series. Fan ...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 148
... or accessible 1 12 SFP 1000BASE-SX P11DCP3 Yes output truncated ---------! NOTE: This parameter is not supported, if you want to the Usage Information section). displays a specific interface configuration. S-Series, Z-Series Syntax Parameters show interfaces - Defaults Command Modes none CONFIGURATION 148 FTOS#show inventory (S-Series and Z-Series) Display the S-Series or Z-Series...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 152
...: up Voltage : ok Serial Number : Part Number : Rev Vendor Id : Date Code : Country Code : FTOS# FTOS#show linecard 11 brief -- show sfm - view information on a specific line card. n/a PP1 - Line card 11 -- Status : online Next Boot : online Required Type : E48PF - 48-port GE line card with SFP optics (EF) Current Type...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 156
... | summary] cp (OPTIONAL) Enter the keyword cp to view CPU usage of the control processor. NOTE: This option is at the process level so process-specific statistics are displayed. 156 The granularity of the Route Processor 1. C-Series, E-Series Syntax Parameters show processes cpu (C-Series and E-Series) View CPU usage information based...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 162
...-unit - displays Layer 2 ACL data for the selected stack member and stack member port-pipe. show hardware layer2 acl - displays CPU usage information based on a specific S-Series stack member. displays information on all interfaces on processes running in the S-Series. Related Commands show hardware system-flow -

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 176
... {status | topology}] brief stack-unit unit-id stack-ports status | topology (OPTIONAL) Enter the keyword brief to the S4810 only. For all stack members or a specific member. Both ends of all other S-Series, the unit ID range is 0-11. SFM side down - S-Series, Z-Series Syntax Parameters show system (S-Series and Z-Series...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 179
... (OPTIONAL) Enter the keyword linecard followed by the linecard number to view information relating to a specific linecard. (OPTIONAL) Enter the keyword page to view 24 lines of data from other show commands, the information necessary for Dell Force10 technical support to the file options. Press the SPACE BAR to view the next line...

FTOS Command Line Reference Guide for the Z9000 System FTOS 9.1.(0.0)

Page 180
The save flash:// result This display output is displayed when you to interrupt the command output. The save specific information of the same information that is an accumulation of a show tech-support page ----------- Usage Information Example (...12 15:39:17 IST 2006 Build Path: /sites/maa/work/sw//C-SERIES/SW/SRC Dell Force10 uptime is 18 minutes System image file is continuous. show version Dell Force10 Networks Real Time Operating System Software Dell Force10 Operating System Version: 1.0 Dell Force10 Application Software Version: FTOS 7.5.1.0 Copyright (c) 1999-2007 by...

Force10 Z9000 Specifications - Dell