FTOS Configuration Guide for the S60 System FTOS 8.3.3.8
Page 37
Install necessary USB device drivers (internet connection required). Pin Assignments Between the E-Series Console and a DTE Terminal Server (continued) E-Series Console Port RJ-45 to RJ-45 Rollover Cable Signal RJ-45 pinout RJ-45 Pinout NC 7 2 CTS 8 1 RJ-45 to access the S60. Getting Started | 37 Table 3-1. Contact Dell Force10 TAC for CD, if necessary...
Install necessary USB device drivers (internet connection required). Pin Assignments Between the E-Series Console and a DTE Terminal Server (continued) E-Series Console Port RJ-45 to RJ-45 Rollover Cable Signal RJ-45 pinout RJ-45 Pinout NC 7 2 CTS 8 1 RJ-45 to access the S60. Getting Started | 37 Table 3-1. Contact Dell Force10 TAC for CD, if necessary...
Installing the S60 System
Page 36
...you connect both the console port and the USB-B port, the S60 system defaults to the USB-B port. Table 6-1 lists the pin assignments. The USB-B connector port is labeled on the left of the S60 system. You will also require the appropriate drivers for system access: a console port and a... USB-B Console Port The S60 system has two management ports available for the USB device in use. NOTE: Before starting this procedure, be sure you have a terminal emulation program already installed on the rear of the management ports on your PC. For assistance, contact Dell Force10 Technical...
...you connect both the console port and the USB-B port, the S60 system defaults to the USB-B port. Table 6-1 lists the pin assignments. The USB-B connector port is labeled on the left of the S60 system. You will also require the appropriate drivers for system access: a console port and a... USB-B Console Port The S60 system has two management ports available for the USB device in use. NOTE: Before starting this procedure, be sure you have a terminal emulation program already installed on the rear of the management ports on your PC. For assistance, contact Dell Force10 Technical...
Installing the S60 System
Page 37
... an XP operating system). 2 Connect the USB-A end of cable (included) into an available USB port on the PC. 3 Connect the USB-B end of cable into the USB-B console port on the S60 system. 4 Power on the S60 system. 5 Install the necessary USB device drivers (an internet connection is required). For assistance, contact Dell Force10 Technical Support. 6 Open your terminal...
... an XP operating system). 2 Connect the USB-A end of cable (included) into an available USB port on the PC. 3 Connect the USB-B end of cable into the USB-B console port on the S60 system. 4 Power on the S60 system. 5 Install the necessary USB device drivers (an internet connection is required). For assistance, contact Dell Force10 Technical Support. 6 Open your terminal...
Quick Start Guide
Page 21
... system recommended). 2 Connect the USB-A end of cable (supplied) into an available USB port on the PC. 3 Connect the USB-B end of the chassis. Contact Dell Force10 TAC for CD, if necessary. Pin Assignments Between the Console and a DTE Terminal Server S55/S60 RJ-45 to RJ-45 Rollover... DB-9 Pin Signal NC 2 7 6 DSR TxD 3 6 2 RxD GND 4 5 5 GND GND 5 4 5 GND RxD 6 3 3 TxD NC 7 2 4 DTR CTS 8 1 7 RTS USB-B Console The USB-B connector port is labeled on the chassis. 5 Install necessary USB device drivers (internet connection required). Table 2-1.
... system recommended). 2 Connect the USB-A end of cable (supplied) into an available USB port on the PC. 3 Connect the USB-B end of the chassis. Contact Dell Force10 TAC for CD, if necessary. Pin Assignments Between the Console and a DTE Terminal Server S55/S60 RJ-45 to RJ-45 Rollover... DB-9 Pin Signal NC 2 7 6 DSR TxD 3 6 2 RxD GND 4 5 5 GND GND 5 4 5 GND RxD 6 3 3 TxD NC 7 2 4 DTR CTS 8 1 7 RTS USB-B Console The USB-B connector port is labeled on the chassis. 5 Install necessary USB device drivers (internet connection required). Table 2-1.
