Service Manual
Page 174
... sunlight or room light, the unit may separate from domestic waste. If toner scatters on , the front cover is open and the Status LED is lifted automatically.... (Fig.5-5) Make sure you fit the toner cartridge properly, or it separate from the drum unit when you pick up the drum unit tightly so that toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5130/5140/5150D... the printer. When the toner cartridge is installed correctly, the blue lock lever is red. (7) To reset the drum counter, press and hold down the Go button until ...
... sunlight or room light, the unit may separate from domestic waste. If toner scatters on , the front cover is open and the Status LED is lifted automatically.... (Fig.5-5) Make sure you fit the toner cartridge properly, or it separate from the drum unit when you pick up the drum unit tightly so that toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5130/5140/5150D... the printer. When the toner cartridge is installed correctly, the blue lock lever is red. (7) To reset the drum counter, press and hold down the Go button until ...
Service Manual
Page 192
... open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5130) No paper (HL5140/5150D/5170 DN) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge with the control panel button. Load paper into...
... open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5130) No paper (HL5140/5150D/5170 DN) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge with the control panel button. Load paper into...
Service Manual
Page 260
......>Command prompt Since the DOS window is ON. Re-writing may be impossible if writing procedure goes wrong. 4) After finishing writing, all the LEDs light up. Status LED (red) blinking) Even if the batch file is completed, the data is sent to the printer. So, be created. (START>Setting>Printer) Delete the created... transmitted or the writing procedure continues. Holding down the Windows system, turn the printer off, unplug the cable and turn the PC off the printer. HL-5130/5140/5150D/5170DN SERVICE MANUAL 1.
......>Command prompt Since the DOS window is ON. Re-writing may be impossible if writing procedure goes wrong. 4) After finishing writing, all the LEDs light up. Status LED (red) blinking) Even if the batch file is completed, the data is sent to the printer. So, be created. (START>Setting>Printer) Delete the created... transmitted or the writing procedure continues. Holding down the Windows system, turn the printer off, unplug the cable and turn the PC off the printer. HL-5130/5140/5150D/5170DN SERVICE MANUAL 1.
Service Manual
Page 261
...Status LED (orange) blinking.) (While writing the firmware; Status LED (red...) blinking) Even if the batch file is completed, the data is fixed to "987654321". Keep the Go button and Job Cancel button until the Status... LED (green) turns on from blinking. Example) FW51NET LZ0004_A.BLF + ENTER Data is sent to the printer; Press the Go button again for HL...the Status LED...now READY status. 4)...and Status LED...
...Status LED (orange) blinking.) (While writing the firmware; Status LED (red...) blinking) Even if the batch file is completed, the data is fixed to "987654321". Keep the Go button and Job Cancel button until the Status... LED (green) turns on from blinking. Example) FW51NET LZ0004_A.BLF + ENTER Data is sent to the printer; Press the Go button again for HL...the Status LED...now READY status. 4)...and Status LED...