Asus AP200 Support and Manuals
Get Help and Manuals for this Asus item
Popular Asus AP200 Manual Pages
Hardware Reference - Page 2
... of the manual revision number. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. Copyright © 1999 ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified...
Hardware Reference - Page 3
....tw/pub/ASUS
ASUS COMPUTER GmbH (Europe)
Marketing
Address: Harkort Str. 25, 40880 Ratingen, BRD, Germany
Telephone: 49-2102-445011
Fax:
49-2102-442066
Email:
[email protected]
Technical Support
Hotline: 49-2102-499712
BBS:
49-2102-448690
Email:
[email protected]
WWW:
www.asuscom.de
FTP:
ftp.asuscom.de/pub/ASUSCOM
AP200 Hardware Reference Guide
3
Hardware Reference - Page 5
...
4-10. Appendix
i. ASUS Barebone Servers 32
AP200 Hardware Reference Guide
5 Long Card Guide 26
4-8. Air Circulation System 25 Fan Replacement 25
4-7. Power Information 28 Output Voltage Regulation 28 Output Current Capacity 28
V. ASUS RAID Solutions 31
iv. System Speaker 26
4-9. Contents
4-2. SCSI Cable Limits 29
ii. Motherboard 19 Motherboard Screws 19 Chassis...
Hardware Reference - Page 7
...setting up the server. The following checklist provides a guideline as follows:
I. Components This is intended for experienced users and integrators with this reference guide as to the necessary components for 68-pin Ultra2 SCSI cables CD-ROM, SCSI, Motherboard SCSI, CD-ROM, Motherboard
ASUS RAID Card Solutions (you additional information to complete this server. Hardware Setup...
Hardware Reference - Page 8
Features
The AP200 is a group server configured on the ASUS P2B-DS/P2B-D smart motherboard which uses the 440BX chipset from Intel and supports two Pentium III/II processors and 100MHz front side bus in the appendix.
• Adaptec AIC-3860 transceiver chip enables Ultra2 SCSI and legacy SCSI ...
Hardware Reference - Page 9
... following safety instructions any time ...; Before opening the chassis panels, make sure all power cables are needed to install or remove the components in this server must be hot.
Operation Safety
IMPORTANT &#...authorized dealer. • It is detected, contact your server, carefully read all the manuals
included with the server package. • Before using the server, make sure all ...
Hardware Reference - Page 11
... your motherboard's User's Manual in ... power source such
as CPU, memory, hard disk drives, and expansion cards. AP200 Hardware Reference Guide
11 Preparation
1. This server uses an ATX power supply that has a fixed ... order to prevent unauthorized access. Set the power supply input voltage to prevent electrical shocks when working on the front. Install final server components such as ...
Hardware Reference - Page 14
Hard Disk Drive F. Fan Module G. Chassis Fan L. Floppy Disk Drive D. 3.5" Device Cage E. Hard Disk Drive Carrier Plate J. II. Power Supply K. Speaker H. CD-ROM Drive B. 5.25" Device Cage C. Components
I . Stabilizing Link Bar M. Components
Side View
Side View
II. Motherboard
14
AP200 Hardware Reference Guide Long Card Guide I A
J
B
C K
D E L
F
M G H
A.
Hardware Reference - Page 16
... server does not come with any pre-installed software. NOTE When installing Windows NT 4.0 or higher operation system, use the Windows NT installation floppy disks. If the Power On LED does not light, make BIOS settings by pressing before Setup begins.
16
AP200 Hardware Reference Guide "Power On" lights when the motherboard receives power from the power supply...
Hardware Reference - Page 19
...). IV. Hardware Setup
Stabilizing Link Bar
The stabilizing link bar needs to be removed in the Chassis
AP200 Hardware Reference Guide
19 To remove ...motherboard or remove the 3.5" device cage. Doing so may damage your motherboard. Motherboard
Read the motherboard User's Manual for details. IV. Motherboard Screws
Screw the motherboard as circled.
HW Setup
Motherboard
Motherboard...
Hardware Reference - Page 20
... LED
White Green (+) Power LED White
20
AP200 Hardware Reference Guide To enable this function, Jumper18 must be set to Enable and an external battery must be ...Setup
Motherboard
P2B-D/DS Chassis Intrusion Photo Sensor
Panel Connections
Several wires should disable Jumper18 to the motherboard's external battery connector. Hardware Setup
Chassis Intrusion Photo Sensor
This motherboard...
Hardware Reference - Page 24
... proper signal stability, a special twisted ribbon cable must be used to connect the SCSI hard drive to the motherboard.
Red Stripe of the Signal Cable Red Stripe of the chassis top panel. Hardware Setup
Mounting the Hard Drive above the Power Supply
Insert the carrier plate and hard disk drive into the...
Hardware Reference - Page 26
Press the plastic clips with a screwdriver to release.
26
AP200 Hardware Reference Guide HW Setup
Card Guide / Speaker
Press the clips with a screwdriver as shown here. Press the clip (or pry from the front of the chassis, you may want to remove the long card guide first. To remove the speaker, press the metal clip (or...
Hardware Reference - Page 31
...; Automatic bad sector reassignment • Supports both global and
local spare drive operation • Background rebuilding • PCI rev. 2.1 compliant • Up to -SCSI RAID Controller • Supports 5x86 RAID processor and two 72-pin SIMM sockets for easy heat dissipation • 350W redundant power supply
V. Appendix
ASUS RAID Solutions
AP200 Hardware Reference Guide
31
Hardware Reference - Page 32
Memory Onboard Fixed Storage Hot-Swap Trays
Support
(GB)
(Channels) Devices
AP100
1
1
1
3
0
AP200
2
1
1
3
0
AP2000
2
1
1
4
3 or 5*
AP2500
2
1
1
4
3 or 5*
AP3000 2 Xeon™
2
2
4
3 or 5*... AP8000
Value Servers AP2000 AP2500 AP3000
Group Servers AP100 AP200
V. Appendix
ASUS Barebone Servers
Rack Mountable
32
AP200 Hardware Reference Guide V. Appendix
iv....
Asus AP200 Reviews
We have not received any reviews for Asus yet.