Netgear HE102 - Wireless Access Point Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear HE102 manuals!
Problems with Netgear HE102?
Ask a Question
Free Netgear HE102 manuals!
Problems with Netgear HE102?
Ask a Question
Most Recent Netgear HE102 Questions
He 102 Installation
I lost the installation CD, how can I setup my HE102 device
I lost the installation CD, how can I setup my HE102 device
(Posted by ybakhash 12 years ago)
Popular Netgear HE102 Manual Pages
HE102 Reference Manual - Page 2
...product(s) or circuit layout(s) described herein.
NETGEAR does not assume any other antenna or radio transmitter. Installers and end-users must be installed to which can be determined by turning ...Model HE102 Wireless Access Point) does not exceed the Class B limits for this device must follow the installation instructions provided in this document without notice. If this user guide...
HE102 Reference Manual - Page 5
.../DSL Router
3 Lower level of the HE102 Wireless Access Point are: ♦ Reliable IEEE 802.11a standards-based wireless technology. ♦ Interfaces directly to 10Mbps IEEE 802.3 Ethernet and IEEE802.3u Fast
Ethernet networks. ♦ Roaming support between the wireless nodes is available to simplify your network setup or to improve data transfer rate. ♦...
HE102 Reference Manual - Page 9
..., the access points are not user configurable.) This encryption key will be configured to information theft. There are configured to generate a 64-bit encryption key. (The 24 factory-set bits are configured with the same ESSID can be used to perform a checksum on the original message.
By default, IEEE 802.11 wireless devices operate in NETGEAR...
HE102 Reference Manual - Page 10
... each with a different legal maximum power output. Though the lower 200 MHz is not supported in the encryption process is 64 bits wide.
transmitted via the wireless interface.
Encryption Key... in HE102 Wireless Access Point.
8 U-NII Band Frequency (GHz) Max. Some vendors may refer to the forty-bit WEP data encryption method, the remaining 24 bits are factory set and not user configurable...
HE102 Reference Manual - Page 13
... 3-INSTALLATION
Installation Overview
Please follow these instructions to work with the wireless adapters and then restart them. 6.
Test the connection. Package Contents
This product package should contain:
♦ HE102 54 Mbps 802.11a Wireless Access Point ♦ Power Adapter and Cord (3.3Vdc, 3.7A) ♦ HE102 User's Guide ♦ Category 5 Ethernet Cable - 25 feet ♦ Support...
HE102 Reference Manual - Page 14
... data transfer rate on the NETGEAR Web page at: http://www.NETGEAR.com. Please call the reseller or customer support in your area. You should keep the Support Information Card, along with the original packing materials, and use the packing materials to repack the HE102 Wireless Access Point if you to allow easy firmware upgrade from remote
locations
12
HE102 Reference Manual - Page 15
Additionally, the HE102 Wireless Access Point supports the following wireless features: ♦ Distributed coordinated function (CSMA/CA, ... ♦ Authentication Algorithm (Open System, Shared Key) ♦ Roaming among access points on the same subnet
LED Indicators
The HE102 Wireless Access Point provides three green status LEDs: Power, Ethernet and Wireless.
Power Ethernet Wireless
13
HE102 Reference Manual - Page 17
... default Service Set Identification (SS ID) is "Wireless," however, you will be able to communicate with the access point, you must be connecting the access point to the Ethernet network so that computers with the 802.11a Wireless Adapter will need to determine the network settings of your Wireless Network
Before installing the HE102 Wireless Access Point, you should you use The HE102...
HE102 Reference Manual - Page 19
... only the power adapter supplied with the HE102 Wireless Access Point, otherwise the HE102 may use the included category 5 UTP Ethernet cable to a 10 Base-T network hub, switch or router.
3. If the connection is a 100 Mbps connection, the light is receiving or transmitting wireless data.
17 Check the setup. It might take a few seconds after...
HE102 Reference Manual - Page 20
... web browser on the bottom of your access point. NETGEAR's HE102 Web Server home page will automatically find the name of your access point, refer to this, "netgear10d4b5," where "10d4b5" is the last 6 digits of the MAC address of your access point in the
Address or Location box. CHAPTER 4-ACCESS POINT CONFIGURATION
The HE102 Wireless Access Point can be similar to the labels...
HE102 Reference Manual - Page 21
... choosing Password from the HE102 Web Server home page. 2. Note: You may change the password at any menu option. If this point by specifying either the IP address or the access point name of the HE102 within the same subnet. 3.
The Enter Network Password window will be displayed. If you must enter the default user name "admin" with the default password "1234...
HE102 Reference Manual - Page 23
..."full", "half", "quarter", "eighth", "and "min". It can go up to match the access point SSID in infrastructure mode, this field; Default: Full
Beacon Interval
Specifies the Beacon Interval value. Wireless LAN Configuration Parameters
CONFIGURATION DESCRIPTION
SSID (Service Set ID)
Enter a 32-character (maximum) service set ID (SSID). The wireless channel in this field defines the...
HE102 Reference Manual - Page 24
... default gateway automatically from the HE102 Web Server home page.
2. Choose the TCP/IP setup option from the DHCP server if the DHCP is enabled.
CONFIGURATION MAC Address IP Address Subnet mask Default gateway
DHCP Client
DESCRIPTION
Displays the MAC address of the access point. TCP/IP Setup
To set the TCP/IP settings, complete the following: 1. Default: Enable
22 Default...
HE102 Reference Manual - Page 28
... current state of the access point and all the stations currently part of its Basic Service Set (BBS). ♦ Choose the Station List option from the HE102 Web Server home page.
26 Please check the NETGEAR support website: http://www.Netgear.com for the latest firmware and upgrade procedure. Firmware Upgrade
The Firmware Upgrade menu options will display the Firmware Upgrade window so that you...
HE102 Reference Manual - Page 29
... are lit on . the one that came with your computer and the HE102
name.
Replace it is powered on the access point. • Make sure the power cord is properly connected to the access point. • Make sure the power adapter is bad. CHAPTER 5-TROUBLESHOOTING
PROBLEM I cannot get onto the Ethernet network from a computer connected to the Ethernet...
Netgear HE102 Reviews
We have not received any reviews for Netgear yet.