NEC VT660K - XGA LCD Projector Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC VT660K Manual Pages
User Manual - Page 2
... any part inside of this manual. However, there is no guarantee that important information concerning the operation and maintenance of the unit. Do not place your projector. Do not place heavy objects on the surface of the projector.
7.
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your NEC VT660K/ VT460K/VT560 Projector and...
User Manual - Page 3
...) (Screwdriver: 24C07231)
Lamp Replacement
• To replace the lamp, follow all instructions provided on the left side (when seen from the wall outlet under any metal objects such as the pieces of its usable life, the lamp bulb may cause injury. Ensure that there is turned off the projector. Fire and Shock Precautions
1. Handle the power cable carefully...
User Manual - Page 4
...31
Cleaning or Replacing the Filter E-31 Cleaning the Cabinet and the Lens E-31
TROUBLESHOOTING E-32
Power Indicator ...E-32 Status Indicator ...E-32 Lamp Indicator ...E-32 Common Problems & Solutions E-33
SPECIFICATIONS E-34
APPENDIX E-35
Cabinet Dimensions ...E-35 Pin Assignments of Image [Cinema Position](for Wireless Remote Control E-10
INSTALLATION AND CONNECTIONS E-11
Setting Up...
User Manual - Page 5
...) image are trademarks of their respective holders. The projector must be in accordance with NEC's Advanced AccuBlend on a ceiling yourself. In addition, the ceiling must be strong enough to support the projector and the installation must be used wirelessly.
*1 Do not attempt to mount the projector on VT460K. About this user's manual may save you 'll find an overview.
TV...
User Manual - Page 7
... is not attached properly or the projector has overheated. POWER Indicator When this light remains orange, it indicates that you that an error has occurred, the lamp cover is magnified, the SELECT GHFE...lamp mode is set to select the menu of the RGB, VIDEO or S-VIDEO input is enabled. To turn on page E-32 for more details.
4. STATUS Indicator If this light appears, replace the lamp...
User Manual - Page 24
...PAL-N, PAL60, SECAM
Power Management On, Off
Noise reduction
Off, Low, High
Auto Adjust
On, Off
Horizontal
Vertical
Clock
Phase
Communication Speed 4800, 9600, 19200
Information Page1 Page2 Page3
Source Index, Horizontal Frequency, Vertical Frequency, Sync Polarity Signal Type, Video Type, Sync Type, Interlace Remaining Lamp Time, Lamp Hour Meter, Filter Usage, Projector Usage
Default...
User Manual - Page 27
... adjusts the vertical position of copyrights which are displaying an image with black borders on -screen instructions.
This is entered, the projector cannot project an image. NOTE: Thermometer symbol indicates the lamp mode is available.
ting image positions.
Setup
To enable the Security function: 1. Select [Advanced] → [Security] and press the F button to increase...
User Manual - Page 29
..." and "Phase") manually.
[Page 1] Source Index Horizontal Frequency Vertical Frequency Sync Polarity
[Page 2] Signal Type Video Type Sync Type Interlace
Adjusting Position/Clock (when Auto Adjust is off and go into standby mode after replacing the lamp. This item has three pages. E-29 Default
[Page 3] Remaining Lamp Time (%)* Lamp Hour Meter (H) Filter Usage Projector Usage * The progress...
User Manual - Page 30
... clock is reset to maintain optimal projector performance. Do not attempt to tighten the screws. Be sure to circumvent this happens, contact your NEC dealer for 2000 hours (up to 3100 hours in Eco mode) of use a lamp other than the NEC replacement lamp (VT60LP). It will appear. To replace the lamp: 1. After you should 3.
socket. CAUTION Do...
User Manual - Page 31
... the filter with a damp cloth. Never use a mild detergent. If heavily soiled, use strong detergents or solvents such as alcohol or thinner.
3. Soap and water will damage the filter membrane. Cleaning
3.
CAUTION • Turn off the projector, turn off the filter (sponge) and replace it is dirty or clogged, your replacement lamp.
Keep out dust and dirt during filter replacement...
User Manual - Page 32
...Off)
Move the projector to Eco mode. -
E-32
Lamp fails to turn on .
TROUBLESHOOTING
This section helps you resolve problems you may encounter while setting up or using the projector. to light.
Status Indicator
Indicator Condition
Projector Condition
Note
Off Blinking light Red
Normal
-
1 cycle (0.5 sec On, Lamp cover error or lamp Replace the lamp cover or
2.5 sec...
User Manual - Page 33
...
Problem Does not turn it on or adjust the image manually with Horizontal / Vertical / Clock / Phase in and that the lamp cover or lamp housing is scrolling vertically, horizontally or both
• Use the RGB, VIDEO or S-VIDEO button on . If there is
insufficient ventilation around the projector or if the room where you and...
User Manual - Page 34
...nec-europe.com/ Global : http://www.nec-pj.com/
*Effective pixels are more than 99.99%. SPECIFICATIONS
This section provides technical information about the VT660K/VT460K/VT560 Projector's performance.
E-34 Model Number
VT660K/VT460K/VT560
Optical LCD Panel
Resolution
Lens
Lamp... Manual zoom and focus: F1.7 - 2.0 f=21.6 - 25.9mm VT660K... Speaker Power Requirement Input Current
Power Consumption...
User Manual - Page 38
... part from overseas)
Fax Line:
+61 8 8375 5757
Email Address: lee.gramola@nec.com.au
WEB Address:
http://www.nec.com.au
(Regions Covered) Australia*, New Zealand
E-38 Please note that this replacement product rental service is being repaired. Note that TravelCare coverage differs in vehicles, boats or ships, etc.
6) Problems or damage caused by using a power cable...
User Manual - Page 41
... Out of Warranty period, NEC Authorized Service Station will Inform estimation of actual service cost to adjust, modify, repair, install or service the product.
6) Any Cross-border charges such as a Warranty repair, but will be done by NEC Authorized Service Station, because of shortage of spare parts due to same model is not sold in the territory.
2) Repair and Return with Loan...
NEC VT660K Reviews
We have not received any reviews for NEC yet.