NEC LT158 - MultiSync XGA LCD Projector Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC LT158 Manual Pages
User Manual - Page 1
NEC LT158 / LT157 User's Manual
LCD Projector
LT158/LT157
User's Manual
Printed in Japan 7N8P1211
User Manual - Page 3
English
E-1
CANCEL
LT158/LT157
LCD Projector User's Manual
MENU
SELECT
ENTER
SOURCE AUATDOJUST
ONS/TAND BY
PCACCCASRETSDASTPUOSWER
User Manual - Page 4
... BE DONE BY QUALIFIED NEC SERVICE PERSONNEL. in a particular installation. If this equipment does cause harmful interference to radio or television reception, which the receiver is dangerous to the equipment as possible, and should be installed as near to make any kind of contact with this user's manual may be easily accessible. NO USER-SERVICEABLE PARTS INSIDE.
CAUTION
This...
User Manual - Page 5
... a wall.
2. b. In addition, the ceiling must be strong enough to support the projector
and the installation must be scattered in direct sunlight, near heaters or heat
radiating appliances. 4. Please consult your dealer for lamp replacement. • Allow a minimum of ONE minute to elapse after the lamp has reached the end of heat inside your hands due...
User Manual - Page 6
... (playback E-43 Capturing Images Displayed on your PC (PC Card Viewer Utility 1.0) ....... TROUBLESHOOTING
Power / Status Light Messages E-50 Common Problems & Solutions E-50
6. MAINTENANCE
Replacing the Lamp E-48 Cleaning or Replacing the Filters E-49
5. INTRODUCTION
Introduction to the LT158/LT157 Projector E-5 Getting Started E-5 What's in the Box E-6 Getting to Know Your...
User Manual - Page 7
...(with any local building codes. TV standard for NTSC playback on the supplied CD-ROM.
*5 The USB terminal meets the USB1.1 specification and accepts a USB mouse only. This applies only to analog RGB signal.
*3 LT158 only.
*4 The PC Control Utility 1.0 is one of the very best projectors available today. E - 5 The remote control can be permanently...
User Manual - Page 11
...to exit "Menus". Please replace the lamp." appears continually until the lamp is on LT158] → Video &#...projector is replaced. See the Power / Status Light Messages on and off the projector, press and hold this button to switch between sources.
7. when the indicator is orange, it indicates that the projection lamp has exceeded 1500 hours (2500 hours in the adjustment or setting...
User Manual - Page 23
... player with component outputs or Video output. Turn on your projector to the RGB INPUT connector on the projector.
E - 21 VGA signal cable (supplied)
Gender changer mini D-Sub 15p F - 15p F (not supplied)
LT158
You can connect your projector. NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements...
User Manual - Page 34
...It is also referred to cancel your setting.
E - 32 Tab:
Indicates a group of adjustment. Selecting on the remote control to the front.
Slide bar:
Indicates settings or the direction of features in a ...menu. You will return to turn the option On.
Toolbar:
Contains several icons for specific tasks.
Radio button: Use this round button to select an option in the square box...
User Manual - Page 35
...move on what is connected to your remote control to highlight the menu for ...Setup View
Drag
Next Stop Select Delete A press of the projector. See page E-42 for RGB and Component).
Play Plays back automatically or manually depending on LT158... image for Video (Not valid for installing the PC Card Viewer Utility. green ... - 33 RGB (DVI on the set- A launcher will get the slide that ...
User Manual - Page 40
... to save your current keystone settings.
E - 38 To reset the lamp usage hour, press "OK". Do this button appears a confirmation dialog box.
Off User can set to "On", the projector automatically determines the best resolution for an active source in the Projector mode.
NOTE: When the confirmation message is on the remote control to change once affects...
User Manual - Page 42
... part of remaining bulb life. Information: Displays the status of lamp and projector ...only when a USB mouse is set to 100 Hours and starts ...Lamp Hour Meter (H) Filter Usage (H) Projector Usage (H)
Color
Clear
Drag Drags to move to draw. E - 40 View Hides the tool bar by left -clicking. Right-clicking anywhere on the remote...different thickness from the NEC logo to display the...
User Manual - Page 43
...instructions for displaying lists of slides and editing • PC Card Viewer PPT Converter 1.0 [Add-In Version] converts files
created with the projector. Grasp the edges of slides or any specific...projector. Eject button
C CARD
MENU
SELECT
ENTER
AC IN
USB
PC CONTROL
VIDEO
S-VIDEO
RGB
CANCEL
SOURCE AUATDOJUST
ONS/TAND BY
PCACCCASRETSDASTPUOSWER
AUDIO
Install...; Set the...this manual)...
User Manual - Page 45
...specific folder. View ..........
Play Plays back automatically or manually depending on the setting on Page 2 of the menu. This allows you to 12 indexes can be displayed on the cabinet is pressed in the right bottom is selected. Pressing the MENU button or clicking with the projector. on the remote... 43 Projecting slides
1. Prev Play Jump Setup View
Drag
Next Stop Select Delete
The ...
User Manual - Page 50
... install a new lamp, select [Menu] → [Projector Options] → [Setup]→[Page 4]→[Clear Lamp Hour Meter] to circumvent this happens, be working, replace it in the cabinet will turn on the remote control for the lamp to prevent the risk of electrical shock. Even though the lamp may cause injury. Do not touch them as the pieces of service...
NEC LT158 Reviews
We have not received any reviews for NEC yet.