NEC 42XM5 - PlasmaSync - 42" Plasma Panel Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC 42XM5 Manual Pages
42XM5/50XM6/60XM5 UM - Page 3
... to provide long, trouble-free service. Handle the unit carefully when installing it is particularly hot, move the monitor to a cooler location, and wait for any bodily harm or damage caused if unqualified persons attempt service or open the cabinet which the plasma monitor is in long term use or continuous operation take the following instructions. Do not...
42XM5/50XM6/60XM5 UM - Page 5
... off timer En-13
WIDE Operations En-14 Wide Screen Operation (manual En-14
When viewing videos or digital video discs En-14 Wide Screen Operation with STB En-40 Troubleshooting En-41
Picture Settings Menu En-21
Table of Signals Supported En-42
Adjusting the picture En-21 Setting the picture mode according to the brightness
of...
42XM5/50XM6/60XM5 UM - Page 6
... accessory.
Drawing A
Drawing B
Ventilation Requirements for installing. • After installation, take appropriate measures to prevent the plasma from tipping over or falling. • Make sure to move or install the device with the screen face down with more than one of the following the installation manual of the optional accessory. • Install the device in damage to the...
42XM5/50XM6/60XM5 UM - Page 10
... set for use with an
RGB or component source. En-9 I JK
A AC IN Connect the included power cord here.
H RGB3 (DVI 24pin) Connect a digital signal (TMDS) from a computer, etc. J REMOTE IN Connect the remote cable to the remote control's remote jack to the audio input from the audio menu screen. L Handles Use when installing or carrying the plasma monitor...
42XM5/50XM6/60XM5 UM - Page 11
... video image corresponds to your speaker's owner's manual.
I JK
A AC IN Connect the included power cord here. L Handles Use when installing or carrying the plasma monitor. F RGB2/ DVD2/ HD2
RGB2:
You can be set for use with an RGB3.
This input can connect an analog RGB signal
and the syncronization signal. En-10 Please refer...
42XM5/50XM6/60XM5 UM - Page 12
...screen. En-11
here. I JK
A AC IN Connect the included power cord here. K REMOTE OUT Connect the remote cable to the REMOTE IN jack of the other display monitor to your speaker's owner's manual...set...REMOTE IN Connect the remote cable to the remote control's remote jack to the EXT SPEAKER terminal on both LEFT and RIGHT channels. L Handles Use when installing or carrying the plasma monitor...
42XM5/50XM6/60XM5 UM - Page 16
... the United States.
Press the WIDE button again. Information Ⅵ Supported resolution See page En-42 for details on the display output of the various VESA signal standards supported by the monitor. Ⅵ "PICTURE SIZE" setting When the setting of time without using gray bars. FULL size screen
The image is true resolution. Note: Do not allow 4:3 content...
42XM5/50XM6/60XM5 UM - Page 42
...or picture is unstable. If the room where the monitor is installed is pressed. En-41 Troubleshooting
If the picture quality is poor or there is ...remote cable from the monitor.
• Set the Control Lock to the proper resolution. • Check the input signal.
• Promptly switch off 5 seconds after powering on screen. It indicates that the power supply circuit, plasma display...
42XM5/50XM6/60XM5 UM - Page 47
...play
(DDC1, DDC2b, RGB3: DDC2b only), Enhanced
Split Screen, Protocol Set, etc. Accessories
Power cord (ן1), Remote control (ן1), AAA batteries (ן2), Manuals (Start up Guide and CD-ROM), Ferrite cores for power cord (ן2), bands for power code (ן2), Cable clampers (ן3), beads...
42XM5/50XM6/60XM5 UM - Page 48
... bands (ן3), Ferrite core for remote cable (ן2).
If you do experience
such a problem please contact NEC Corporation of America and also
the manufacturer of them under "BNC INPUT".
*3 Compatible with standards from
the source equipment (DVD, Set-top box, etc.). Specifications
Ⅵ 50XM6
Screen Size
43.4 inches(H)ן24...
42XM5/50XM6/60XM5 UM - Page 49
... (50 Hz) 1080P (60 Hz)
*2 The 5-BNC connectors are in inch (mm)
The features and specifications may not be displayed
properly. Accessories
Power cord (ן1), Remote control (ן1), AAA batteries (ן2), Manuals (Start up Guide and CD-ROM), Ferrite cores for power cord (ן2), bands for power...
42XM5/50XM6/60XM5 UM - Page 50
... Warranty Plasma Monitors
NEC Corporation of America warrants this product to be free from defects in material and workmanship under the following terms and, subject to the conditions set forth below , this warranty covers all other warranties expressed or implied, including, but we will not pay labor and material expenses for (1) one year from : a. Replacement parts...
42XM5/50XM6/60XM5 UM - Page 201
... with Part 15 of Product:
Plasma Display
Equipment Classification:
Class B Peripheral
Models:
PX-42XM5A
We hereby declare that the equipment specified above conforms to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. No.:
NEC CORPORATION...
42XM5/50XM6/60XM5 UM - Page 202
... OF AMERICA 1250 N. NEC and the NEC logo are registered trademarks of NEC Corporation
NEC Corporation of FCC Rules. DECLARATION OF CONFORMITY
This device complies with Part 15 of America 1250 N. U.S.
Arlington Heights Road, Suite 400 Itasca, Illinois 60143-1248 800-836-0655
Type of Product:
Plasma Display
Equipment Classification:
Class B Peripheral
Models:
PX-50XM6A
We hereby...
42XM5/50XM6/60XM5 UM - Page 203
...
This device complies with Part 15 of America 1250 N.
NEC and the NEC logo are registered trademarks of NEC Corporation
NEC Corporation of FCC Rules. No.:
NEC CORPORATION OF AMERICA 1250 N. Arlington Heights Road, Suite 400 Itasca, Illinois 60143-1248 800-836-0655
Type of Product:
Plasma Display
Equipment Classification:
Class B Peripheral
Models:
PX-60XM5A
We hereby declare...
NEC 42XM5 Reviews
We have not received any reviews for NEC yet.