NEC LCD4215 - MultiSync - 42" LCD Flat Panel Display Support and Manuals
Get Help and Manuals for this NEC item
Most Recent NEC LCD4215 Questions
Where Can I Get A Repair Manual For A Nec Lcd4215 Panel
repair manual
repair manual
(Posted by 19bob41 12 years ago)
Popular NEC LCD4215 Manual Pages
External Control Guide - Page 11
...(0064h) '0'-'0'-'3'-'2' (30h, 30h, 33h, 32h): Current Brightness setting is 50(0032h) as 80% ETX (03h): End of packet
Step 3.
Delimiter CR (0Dh): End of Message
Check code
BCC: Block Check Code Refer to the section 4.5 "Check code" for confirmation.
(11/37) The controller request the monitor to support this operation. The monitor replies with a message for a BCC calculation.
External Control Guide - Page 12
... for a BCC calculation. No error '0'-'0' (30h, 30h): Operation code page number is 0 '1'-'0' (31h, 30h): Operation code is 10h (in temperature sensors. The controller can monitor inside temperatures by using those sensors through RS-232C.
Delimiter CR (0Dh): End of packet
6.2. LCD3215/LCD4215 has two built-in the page 0) '0'-'0' (30h, 30h): This operation is "Set parameter" type...
External Control Guide - Page 13
...): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller 'A' (41h): Monitor ID
LCD3215/LCD4215 must be ASCII 'A' (41h). 'F' (46h): Message Type is "Set parameter reply" '1'-'2' (30h, 32h): Message length is #1. No error '0'-'2' (30h, 32h): Operation code page number is 0 '7'-'8' (37h, 38h): Operation code is 78h (in the page 2) '0'-'0' (30h, 30h): This operation is...
External Control Guide - Page 14
...): Monitor ID
LCD3215/LCD4215 must be ASCII 'A' (41h). '0' (30h): Message sender is the controller 'C' (43h): Message Type is "Get parameter " '0'-'6' (30h, 36h): Message length is 6 bytes
Message STX (02h): Start of Message '0'-'2' (30h, 32h): Operation code page number is 02h. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2) '0'-'0' (30h, 30h): This operation is "Set parameter...
External Control Guide - Page 16
... that can be written to the section 4.5 "Check code" for a BCC calculation.
No error 'C'-'2','0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command The monitor replies same as power control command to the controller. '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Power mode 0001: ON 0002, 0003: Do not set . 0004: OFF (same as the power off by...
Installation Guide - Page 1
LCD4215 Installation Guide
42" LCD Display
Contents:
Product Description and Notes Tilt Angle and Rotation Ventilation Requirements Display Dimensions
Front, Top & Right Side Rear & Bottom New I/O Connections Display Dimensions w/Optional Speakers and Stand Table Top Stand Dimensions Optional Speaker Dimensions Optional Wall Mount Dimensions Control Codes
NEC Display Solutions of 10
Tilt...
Installation Guide - Page 2
NEC Display Solutions of 10
Contact NEC for proper ventilation. If for some reason the opening . www.necdisplay.com
LCD4215
Page 2 of America, Inc.
LCD4215 Installation Guide
42" LCD Display
Ventilation Requirements (all models)
Dimensions below are minimum required for design review and recommendations.
Rev 1.1
WALL
100mm 4" WALL
100mm 4"
Landscape 5 to 40°C 41 to 104&#...
Installation Guide - Page 3
Rev 1.1
(PANEL DISPLAY AREA)
(PANEL DISPLAY AREA)
IR
www.necdisplay.com
LCD4215
Page 3 of America, Inc. LCD4215 Installation Guide
42" LCD Display
Display dimensions
NEC Display Solutions of 10
Installation Guide - Page 4
Rev 1.1
for MOUNT UNIT 4-M6 Depth 11mm
Control Panel
Power Switch
100mm MOUNTING HOLE PATTERN
www.necdisplay.com
LCD4215
Page 4 of America, Inc. LCD4215 Installation Guide
42" LCD Display
Display dimensions (cont.)
NEC Display Solutions of 10
Installation Guide - Page 5
Rev 1.1
New I /O Terminal
NEC Display Solutions of 10 LCD4215 Installation Guide
42" LCD Display
Old I /O Terminal
www.necdisplay.com
LCD4215
Page 5 of America, Inc.
Installation Guide - Page 6
LCD4215 Installation Guide
42" LCD Display
Dimensions with optional speakers and stand
NEC Display Solutions of 10 Rev 1.1
www.necdisplay.com
LCD4215
Page 6 of America, Inc.
Installation Guide - Page 7
LCD4215 Installation Guide
42" LCD Display
Table Top Stand Dimensions (ST-4020)
NEC Display Solutions of 10
Rev 1.1
1.40 0.51 1.86 2.36 5.00 2.89
3.52
3.48
4.94
0.83
0.69
Table Top Stand ST-4020
0.83
13.00
www.necdisplay.com
LCD4215
Page 7 of America, Inc.
Installation Guide - Page 8
Rev 1.1
Optional Speakers SP4020-4620
0.79
INPUT TERMINAL
www.necdisplay.com
LCD4215
Page 8 of America, Inc. LCD4215 Installation Guide
42" LCD Display
Optional Speaker Dimensions (SP4020-4620)
NEC Display Solutions of 10
Installation Guide - Page 9
Rev 1.1
Dimensions with optional Wall Mount Kit (WMK3260-L)
www.necdisplay.com
LCD4215
Page 9 of America, Inc. LCD4215 Installation Guide
42" LCD Display
NEC Display Solutions of 10
Installation Guide - Page 10
... required are not required.
LCD4215 Installation Guide
42" LCD Display
NEC Display Solutions of 10
www.necdisplay.com
LCD4215
Page 10 of America, Inc. Cable Connection
Communication Protocol:
Interface:
RS-232C
Communication: Asynchronous
Baud Rate:
9600 bps
Data Length: 8 bits
Parity: None Stop Bit: 1 bit Communication Code: Hex
PC Control Connector (D-Sub 9P)
NOTE...
NEC LCD4215 Reviews
We have not received any reviews for NEC yet.