Menus and Messages Guide
Page 110
...and then the previous screen appears. The MFP detects after powering on Cable Unplugged that the back side scanner cable is unplugged. 298.02 Scanner Missing - Action 1 Turn the MFP off. 2 Plug the front side scanner cable into its connector. 3 Turn the MFP on . Information The ... function. USB cable in the slot. Understanding MFP messages Message Meaning 298.01 Scanner Missing - The MFP detects after powering on Cable Unplugged that the front side scanner cable is unplugged. Functions disabled transitional messages 110 A user turned off by system panel is disabled...
...and then the previous screen appears. The MFP detects after powering on Cable Unplugged that the back side scanner cable is unplugged. 298.02 Scanner Missing - Action 1 Turn the MFP off. 2 Plug the front side scanner cable into its connector. 3 Turn the MFP on . Information The ... function. USB cable in the slot. Understanding MFP messages Message Meaning 298.01 Scanner Missing - The MFP detects after powering on Cable Unplugged that the front side scanner cable is unplugged. Functions disabled transitional messages 110 A user turned off by system panel is disabled...
Menus and Messages Guide
Page 116
... held jobs were lost 102 38 Memory full 102 39 Page is too complex to [size] [type] 97 Clean scanner backing strip 97 Clean scanner glass 97 Disk corrupted 97 Disk Full - Cable Unplugged 110 30.yy Invalid refill, change cartridge 101 31 Replace defective print cartridge 101 32.yy Replace unsupported print...
... held jobs were lost 102 38 Memory full 102 39 Page is too complex to [size] [type] 97 Clean scanner backing strip 97 Clean scanner glass 97 Disk corrupted 97 Disk Full - Cable Unplugged 110 30.yy Invalid refill, change cartridge 101 31 Replace defective print cartridge 101 32.yy Replace unsupported print...
Service Manual
Page 81
... or not connected properly, reattach or reconnect it . • Accept the configuration change which notifies the printer the option has been hot unplugged (removed with the power on page 2-147. Touch Cancel Job if a scan job is active. Scanning resumes from the ADF immediately after... change which notifies the printer the option has been hot unplugged (removed with the power on . A new scan job containing the same parameters as the previous job starts. During a scanner calibration, the firmware detects that the scanner backing strip for the following actions may be attached to ...
... or not connected properly, reattach or reconnect it . • Accept the configuration change which notifies the printer the option has been hot unplugged (removed with the power on page 2-147. Touch Cancel Job if a scan job is active. Scanning resumes from the ADF immediately after... change which notifies the printer the option has been hot unplugged (removed with the power on . A new scan job containing the same parameters as the previous job starts. During a scanner calibration, the firmware detects that the scanner backing strip for the following actions may be attached to ...
Service Manual
Page 82
...X646e only. Warning: All files stored on page 2-147. 2-44 Service Manual Note: The scanner finishes scanning currently committed pages in the ADF, but the job is not canceled. If this... Insert tray [x] Install Bin x or Cancel Job Description/action During a scanner calibration, the firmware detects that the scanner ADF or flatbed glass may be repaired. 7002-xxx User attendance messages (...continued) Code Sub code Primary message Clean scanner glass Disk corrupted Disk Full - x can be restarted. The hard disk must be 1, ...
...X646e only. Warning: All files stored on page 2-147. 2-44 Service Manual Note: The scanner finishes scanning currently committed pages in the ADF, but the job is not canceled. If this... Insert tray [x] Install Bin x or Cancel Job Description/action During a scanner calibration, the firmware detects that the scanner ADF or flatbed glass may be repaired. 7002-xxx User attendance messages (...continued) Code Sub code Primary message Clean scanner glass Disk corrupted Disk Full - x can be restarted. The hard disk must be 1, ...
Service Manual
Page 131
... problem persists and the exit sensor seems to be malfunctioning. Check for both the flatbed and ADF. Verify that the exit sensor is malfunctioning. models X644e/X646e" on page 6-2. ADF Eject Jam The exit sensor may be operating properly, go to "294.01 Error code service check" on the rear of... .03 287 .13 297 .14 298 .01 Paper Missing Jam An attempt was being staged. Check the cables on the rear of the Side Cable Unplugged scanner is loaded in the ADF input tray or the paper was removed from the ADF input tray just as it was made to force an...
... problem persists and the exit sensor seems to be malfunctioning. Check for both the flatbed and ADF. Verify that the exit sensor is malfunctioning. models X644e/X646e" on page 6-2. ADF Eject Jam The exit sensor may be operating properly, go to "294.01 Error code service check" on the rear of... .03 287 .13 297 .14 298 .01 Paper Missing Jam An attempt was being staged. Check the cables on the rear of the Side Cable Unplugged scanner is loaded in the ADF input tray or the paper was removed from the ADF input tray just as it was made to force an...
Service Manual
Page 132
7002-xxx User attendance messages-paper jams and paper handling errors (2xx.xx) Code Sub code Description Possible causes 298 .02 Scanner Missing-Rear One of the Side Cable Unplugged scanner is found with the cables, go to make sure they are plugged in and fastened securely. Action Check the cables on the rear of the scanner to "298.02 Error code service check" on the rear of the cables on page 2-115. 2-94 Service Manual If no problem is unplugged or loose.
7002-xxx User attendance messages-paper jams and paper handling errors (2xx.xx) Code Sub code Description Possible causes 298 .02 Scanner Missing-Rear One of the Side Cable Unplugged scanner is found with the cables, go to make sure they are plugged in and fastened securely. Action Check the cables on the rear of the scanner to "298.02 Error code service check" on the rear of the cables on page 2-115. 2-94 Service Manual If no problem is unplugged or loose.
Service Manual
Page 153
7002-xxx 298.01 Error code service check-models X644e/X646e Scanner missing-front side cable unplugged.This is the ADF CCD 36 pin ICC cable connected to perform scanner registration. See "Flatbed interconnect card removal" on page 4-33 • ADF CCD assembly. • If ADF CCD assembly is ...and to the motor driver card. See "Flatbed interconnect card removal" on page 4-4. 298.02 Error code service check Scanner missing-rear side cable unplugged. FRU 1 Scanner control card to flatbed inteconnect card cable 2 Motor drive card to flatbed interconnect card cable 3 Motor driver card Flatbed ...
7002-xxx 298.01 Error code service check-models X644e/X646e Scanner missing-front side cable unplugged.This is the ADF CCD 36 pin ICC cable connected to perform scanner registration. See "Flatbed interconnect card removal" on page 4-33 • ADF CCD assembly. • If ADF CCD assembly is ...and to the motor driver card. See "Flatbed interconnect card removal" on page 4-4. 298.02 Error code service check Scanner missing-rear side cable unplugged. FRU 1 Scanner control card to flatbed inteconnect card cable 2 Motor drive card to flatbed interconnect card cable 3 Motor driver card Flatbed ...
Service Manual
Page 164
... Manual Check for approximately +5 V dc at J27 on the system board. Check to make sure the LVPS cable is correct, Go to the system board. Unplug the AC line cord, remove the LVPS from the LVPS and disconnect the LVPS cable to step 9. Remove one option/feature at the +5 V dc test... point on the system board. Note: Use care not to the scanner control card. Unplug the AC line cord from the printer, and check the continuity of the interface card to the printer system board and to short adjacent...
... Manual Check for approximately +5 V dc at J27 on the system board. Check to make sure the LVPS cable is correct, Go to the system board. Unplug the AC line cord, remove the LVPS from the LVPS and disconnect the LVPS cable to step 9. Remove one option/feature at the +5 V dc test... point on the system board. Note: Use care not to the scanner control card. Unplug the AC line cord from the printer, and check the continuity of the interface card to the printer system board and to short adjacent...