User Manual
Page 107
... installed on . The printer disables all communication to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. 54 Standard network software error The printer detects unformatted flash memory when the power is installed, but cannot communicate with it. 51 Defective flash...message and continue printing. • Turn the power off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. • Format the flash memory. If the message remains, the flash memory may be defective and require ...
... installed on . The printer disables all communication to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. 54 Standard network software error The printer detects unformatted flash memory when the power is installed, but cannot communicate with it. 51 Defective flash...message and continue printing. • Turn the power off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. • Format the flash memory. If the message remains, the flash memory may be defective and require ...
Service Manual
Page 43
...data is sent to clear the message and continue printing. Note: Once the error is displayed the first time, reporting of the following: • Press Select ( ) to reset the printer. • Upgrade the network firmware in the printer, and turn it . See "Waste toner bottle removal" ...on to clear the message and continue printing. The printer disables all communications to the associated network interface. Try one or more of further errors is suppressed until the waste ...
...data is sent to clear the message and continue printing. Note: Once the error is displayed the first time, reporting of the following: • Press Select ( ) to reset the printer. • Upgrade the network firmware in the printer, and turn it . See "Waste toner bottle removal" ...on to clear the message and continue printing. The printer disables all communications to the associated network interface. Try one or more of further errors is suppressed until the waste ...
Service Manual
Page 55
... board removal" on page 4-19. Diagnostic information 2-21 Update firmware or replace the controller board. Increment count failed due to maximum value limit. 5025-2xx, 4xx Service error messages (1xx, 9xx) (continued) Error code 957.xx Service System Board 958.xx Service NAND Failure 959....01 Service Invalid Firmware 959.02 Service Invalid Firmware 959.03 Service Invalid Firmware 959.04 Service Invalid Firmware 959.05 Service Invalid Firmware 959.20 Service System...
... board removal" on page 4-19. Diagnostic information 2-21 Update firmware or replace the controller board. Increment count failed due to maximum value limit. 5025-2xx, 4xx Service error messages (1xx, 9xx) (continued) Error code 957.xx Service System Board 958.xx Service NAND Failure 959....01 Service Invalid Firmware 959.02 Service Invalid Firmware 959.03 Service Invalid Firmware 959.04 Service Invalid Firmware 959.05 Service Invalid Firmware 959.20 Service System...
Service Manual
Page 60
... values of the cable at JCARB1 for proper connection to the controller board. Once a component has been installed in another printer. Reload the firmware and try again. Replace the controller board with a new, and not previously installed controller board. Replace the controller board with a new,...No Go to the firmware? Check the cable at JCARB1: JCARB1 Pin Value 4 +24 V dc 6 +24 V dc 8 +24 V dc 9 Ground 12 Ground 13 +24 V dc 15 +24 V dc 17 +24 V dc Are the values approximately correct? Replace the main drive gear assembly. This error code indicates a mismatch...
... values of the cable at JCARB1 for proper connection to the controller board. Once a component has been installed in another printer. Reload the firmware and try again. Replace the controller board with a new, and not previously installed controller board. Replace the controller board with a new,...No Go to the firmware? Check the cable at JCARB1: JCARB1 Pin Value 4 +24 V dc 6 +24 V dc 8 +24 V dc 9 Ground 12 Ground 13 +24 V dc 15 +24 V dc 17 +24 V dc Are the values approximately correct? Replace the main drive gear assembly. This error code indicates a mismatch...