Fujitsu MAP3367NC - Enterprise 36.7 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MAP3367NC manuals!
Problems with Fujitsu MAP3367NC?
Ask a Question
Free Fujitsu MAP3367NC manuals!
Problems with Fujitsu MAP3367NC?
Ask a Question
Most Recent Fujitsu MAP3367NC Questions
Driver For Fujitsu Hard-drive Model Map3367np For Window Nt.
I have got a PC with WINDOW NT for controlling work station. During operating it does not recognise ...
I have got a PC with WINDOW NT for controlling work station. During operating it does not recognise ...
(Posted by onkarsingh431 13 years ago)
Popular Fujitsu MAP3367NC Manual Pages
Manual/User Guide - Page 4
Related Standards
Product specifications and functions described in this manual takes precedence. ii
C141-E166
Document number T10/1236D Rev.20 [NCITS.351:2001] T10/996D Rev.8c [NCITS.306:1998] T10/1157D Rev.20 T10/1365D Rev.7
Title SCSI Primary Commands-2 (SPC-2)
SCSI-3 Block Commands (SBC)
SCSI Architecture Model-2 (SAM-2) SCSI Parallel Interface-4 (SPI-4)
*1 ANSI = American National ...
Manual/User Guide - Page 5
... automatic diagnosis, and maintenance of interface connector.
Chapter 4
INSTALLATION REQUIREMENTS
This chapter describes the basic physical and electrical requirements for setting device number and operation modes, mounting the disk drive, connecting the cables, and confirming drive operation. This chapter also describes diagnostic methods for error analysis and how analyze collected...
Manual/User Guide - Page 8
... read out the error information detected in the field. To avoid shocks, turn the power
off the power before handling. To avoid injury, do not touch the mechanical assembly during servicing or repair. Always ground yourself with a wrist strap connected to clean the disk drive. Do not remove a PCA. Connect the
ribbon cable to the device.
2. Fujitsu 6-7 does not...
Manual/User Guide - Page 15
... Limitation of side-mounting 4-5 Surface temperature measurement points 4-6 Service clearance area ...4-7 Current waveform (+12 VDC 4-8 Power on/off sequence (1) ...4-9 Power on/off sequence (2) ...4-9 Power on/off sequence (3) ...4-9 AC noise filter (recommended 4-11 NP connectors and terminals location 4-11 16-bit SCSI interface connector 4-12 Power supply connector (16-bit SCSI model...
Manual/User Guide - Page 19
...'s system. The MAP series disk drives support the Small Computer System Interface (SCSI) as the powerful command set of the MAP series intelligent disk drives (IDD). The data format can be changed from the format at factory shipment by reinitializing with an embedded SCSI controller.
The flexibility and expandability of the SCSI, as well as described in this manual. C141-E166
1-1
Manual/User Guide - Page 20
... the SCSI bus can be useful with NP model.
The IDD can be connected directly to accommodate future expansion of system functions.
(3) 8-bit SCSI/16-bit SCSI
The IDD has 16-bit data bus width (16-bit SCSI), which have the wide transfer function suitable for details of the disk drive.
For the ultra SCSI model, number of connectable SCSI devices on the same SCSI bus...
Manual/User Guide - Page 29
... Table 2.1 Model names and order numbers
Model name
MAP3147NC MAP3147NP MAP3735NC MAP3735NP MAP3367NC MAP3367NP
Order number
CA06200-B400 CA06200-B460 CA06200-B200 CA06200-B260 CA06200-B100 CA06200-B160
SCSI type
SCA2, LVD 68-pin, LVD SCA2, LVD 68-pin, LVD SCA2, LVD 68-pin, LVD
Capacity Number of Number of the SCSI.
2.1 Hardware Specifications
2.1.1 Model name and order number
Each model has...
Manual/User Guide - Page 34
... as possible as follows. Even if the IDD is used intermittently, the longest service life is 60°C or less. The above does not applied to diagnose and repair a drive malfunction. Failure of the data on the disk is being performed. Therefore, the user must design the system cabinet so that requires repair, adjustments, or replacement.
Manual/User Guide - Page 75
... prevent injury, do not handle the drive until after the device has cooled sufficiently after turning off the power. CHAPTER 5 INSTALLATION
5.1 Notes on Handling Drives 5.2 Connections 5.3 Setting Terminals 5.4 Mounting Drives 5.5 Connecting Cables 5.6 Confirming Operations after Installation and Preparation
for Use 5.7 Dismounting Drives 5.8 Spare Disk Drive
This chapter describes the notes on...
Manual/User Guide - Page 82
Table 5.4 Write protect setting (NP model only)
Write protect Write operation is disable. Table 5.3 Motor start mode
Set how to control the starting of the IDD spindle motor according to the disk medium is disabled.
When this setup terminal is open, the IDD automatically identifies the DIFFSNS signal level on the SCSI bus and the IDD SCSI interface operation mode...
Manual/User Guide - Page 85
... operator panel (if required for NP model)
The general procedures and notes on connecting cables are used .
5.5 Connecting Cables
Connect the IDD and system with the terminating resistor is in Table 4.2 are described below.
Check that the smooth flow of the SCSI connectors.
When the recommended parts listed in use, less than device specifications must be burnt if overcurrent...
Manual/User Guide - Page 90
.... Otherwise, specify 0 in the "number of SCSI Logical Interface Specifications for each model (part number) when shipped from the default format, all sides of logical data blocks after initialization is connected to Chapters 3 and 6 of SCSI Logical Interface Specifications for the SCSI cable connection:
• All connectors including other SCSI devices are as follows. Refer to the...
Manual/User Guide - Page 94
...set. It is recommended to use the default setting in normal operations.
(2) Disconnection/reconnection parameters (page code = 2)
The following parameters are used to optimize the start timing of reconnection processing to evaluate the validity of SCSI Logical Interface Specifications... in consideration of the disk. However, it is recommended to transfer data on the SCSI bus at a read ...
Manual/User Guide - Page 103
... if data is destroyed during servicing or repair. Contact Fujitsu representative to submit information for the disk drive. C141-E166
6-7 (3) Parts that can be replaced in the field
The PCA cannot be included:
a) IDD model, part number (P/N), revision number, serial number (S/N), and date of manufacturing
b) Error status
• Date when the error occurred • System configuration •...
Manual/User Guide - Page 108
... causes include insufficient power capacity, loose cable connection, insufficient timing or insufficient mechanical play, and problems related to check disk drive performance.
The INIT then issues a REZERO UNIT command to return the read/write head to see whether the error was caused by the disk drive. To analyze the error posted in the diagnostic test, reconstruct the conditions...
Fujitsu MAP3367NC Reviews
We have not received any reviews for Fujitsu yet.