Fujitsu MAV2036RC - 36.7 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MAV2036RC manuals!
Problems with Fujitsu MAV2036RC?
Ask a Question
Free Fujitsu MAV2036RC manuals!
Problems with Fujitsu MAV2036RC?
Ask a Question
Popular Fujitsu MAV2036RC Manual Pages
Manual/User Guide - Page 1
C141-E219
Figure 4.1 Dimensions
[Units: mm]
4-1
CHAPTER 4 Installation Requirements
4.1 Mounting Requirements 4.2 Power Supply Requirements 4.3 Connection Requirements
This chapter describes the environmental, mounting, power supply, and connection requirements. 4.1 Mounting Requirements 4.1.1 Dimensions
Figures 4.1 show the ...
Manual/User Guide - Page 2
... should not exceed 5°.
(a) Horizontal -1
(b) Horizontal -2
(c) Vertical -1
(d) Vertical -2
(e) Upright mounting -1
(f) Upright mounting -2
Direction of gravity
Figure 4.2 HDD orientations
4-2
C141-E219 Inclination from the horizontal plane. Installation Requirements
4.1.2 Mounting orientations
The permissible orientations of the HDD are shown in Figure 4.2, the drive can be...
Manual/User Guide - Page 3
... screw from the drive or deface them in Figure 4.3, use M3 × 0.5 metric (2) Examples of mounting frame structure
Special attention must be within the drive specifications. C141-E219
4-3 c) Tightening torque of screw must be 2.5 mm ±0.5 mm.
a) As shown in any way.
(1) The mounting screws must use the frame with an...
Manual/User Guide - Page 4
Vent hole Label
Figure 4.4 Breathing hole location
4-4
C141-E219 Installation Requirements
Figure 4.3 Mounting frame structure (5) Never cover the vent hole as shown in Figure 4.4.
Manual/User Guide - Page 5
...surface temperature at 50°C or below at installed in a cabinet is a condition for assuring an MTBF of 1,400,000 hours, requires an air flow of specific ICs and the DE. Table 4.1 Surface temperature ...of 0.5 m/s or more. Measurement point
1 DE Surface
2 Read channel LSI
3 VCM/SPM Driver
4 HDC
5 MPU
Maximum temperature 60°C 80°C 93°C 92°C 90°C
Figure 4.5 ...
Manual/User Guide - Page 6
... in Figure 4.6.
[Surface Y] • Interface connection
[Surface Z] • Holes for mounting screw
[Surface X] • Holes for mounting screw
(Both Side)
Figure 4.6 Service clearance area
(8) Environmental magnetic field
Do not install the HDD in the vicinity of equipment giving off strong magnetic fields, such as monitors, televisions, or loudspeakers.
(9) Leakage magnetic flux Do...
Manual/User Guide - Page 7
... of spindle motors
After power is used, the spindle motors should be started in the +12V DC line when the spindle motor rotation starts. MAV2073RC
MAV2036RC
Current (500mA/div) Current (500mA/div)
Time (2 sec/div)
Time (2 sec/div)
Figure 4.7 Current waveform (+12V DC)
(3) Power on/off sequence
The order of the...
Manual/User Guide - Page 8
...
To eliminate AC line noise, a noise filter should be installed at 10 MHz • Circuit construction: T-configuration as shown in Figure 4.8 is as follows: • Attenuation: 40 dB or more at the AC input terminal on the HDD power supply unit.
The specification of interface connector. Interface connector (CN1) (power lines included...
Manual/User Guide - Page 9
Table 4.2 lists the signal allocation of the SAS plug on the HDD. S1 S7 P1 P15
S14 S8
Figure 4.10 SAS plug connector overview
C141-E219
4-9
4.3 Connection Requirements
4.3.2 Interface connector Figure 4.10 shows the SAS type interface connector (SAS plug) overview.
Manual/User Guide - Page 10
... Port Transmit(positive) signal GND for SAS Primary Port GND for SAS Secondary Port Not used Not used GND for SAS Secondary Port Not used Not used GND for SAS Secondary Port Not used Not used Not used on MAV2073RC and MAV2036RC.
4-10
C141-E219 Installation Requirements
Table 4.2 Interface connector (SAS plug) signal allocation:CN1
Pin No...
Fujitsu MAV2036RC Reviews
We have not received any reviews for Fujitsu yet.