Fujitsu MAF3364LC - Enterprise 36.4 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MAF3364LC manuals!
Problems with Fujitsu MAF3364LC?
Ask a Question
Free Fujitsu MAF3364LC manuals!
Problems with Fujitsu MAF3364LC?
Ask a Question
Popular Fujitsu MAF3364LC Manual Pages
Manual/User Guide - Page 5
... National Standard for
American National
Information Systems-Small Computer Standards Institute
System Interface (SCSI)
(ANSI)
American National Standard for
American National
Information Systems-Small Computer Standards Institute
System Interface - 2(SCSI-2)
(ANSI)
COMMON COMMAND SET (CCS) American National
of products covered by this manual comply with the following standards.
Manual/User Guide - Page 6
... and MAG series disk drives. PREFACE
This manual describes the MAF3364LC/LP/MC/MP (hereafter, MAF series), MAE3182LC/LP, MAE3091LC/LP, (hereafter, MAE series), and MAG3182LC/LP/MC/MP, MAG3091LC/LP/MC/MP (hereafter, MAG series), 3.5-inch fixed disk drives with an embedded SCSI controller. The model numbers have a basic understanding of model names and product numbers...
Manual/User Guide - Page 8
... height (10,025rpm)
Note 2: Type model name
Type model name
Model name
MAE3182
MAE3182LC, MAE3182LP
MAE3091
MAE3091LC, MAE3091LP
MAF3364
MAF3364LC, MAF3364LP, MAF3364MC, MAF3364MP
MAG3182
MAG3182LC, MAG3182LP, MAG3182MC, MAG3182MP
MAG3091
MAG3091LC, MAG3091LP, MAG3091MC, MAG3091MP
C141-E064-03EN
vii Fujitsu is defined as a failure requiring adjustments, repairs, or replacement.
Manual/User Guide - Page 9
... than
0.5 m/s is on the disk drive before connecting or
disconnecting cables.
2.
Do not connect or disconnect cables when power is required in an environment at 40°C, and an air flow with a wind velocity of terminals except following setting pins during the power is destroyed during servicing or repair. Fujitsu does not assume responsibility if...
Manual/User Guide - Page 10
... Manual
1. SCSI Bus Error Recovery Processing
1. Maintenance and Diagnostics 3. Installation 6. Command Specification 4. Specifications 3. Data Format 4. Diagnostics and Maintenance
1. Installation Requirements 5. General Description 2. Error Analysis 4. Specifications and Equipment Configuration 2. Disk Medium Management
1. SCSI Message 3. Removal and Replacement...
Manual/User Guide - Page 13
...16 68 pin connector 16-bit model (LP/MP 4-16 SCA2 type SCSI model (LC/MC 4-24 Cable connector requirements 4-28 External operator panel 4-29
CHAPTER 5 INSTALLATION 5-1 5.1 Notes on Handling Drives 5-1 5.2 Connections...5-3 5.3 Setting Terminals...5-5 5.3.1 SCSI ID setting...5-6 5.3.2 Each mode setting ...5-7 5.3.3 Mode settings ...5-9 5.4 Mounting Drives ...5-10 5.4.1 Check before mounting...
Manual/User Guide - Page 19
...; Arbitration • Disconnection/reselection • Data bus parity • Command set which meets the logical specification of the SCSI CCS (Common
Command Set for SCSI-2. The IDD can manipulate data through logical block addressing regardless of the physical characteristics of system functions.
(3) 8-bit SCSI/16-bit SCSI
The IDD has 16-bit data bus width (16-bit...
Manual/User Guide - Page 31
...) command support SCSI-3 command partial support
2 MB FIFO ring buffer (LC/LP models), 4 MB FIFO ring buffer (MC/MP models), multi-segment buffer: Segment count 1 to 215,040
0.7 ms (Read)/ 0.9 ms (Write) 5.5 ms (Read)/ 6.0 ms (Write) 12.0 ms (Read)/ 13.0 ms (Write) 30 s typ. (60 s max.)
30 s typ. 2.1.2 Function specifications Table 2.1 shows the function specifications of rotations (rpm...
Manual/User Guide - Page 34
... diagnose and repair a drive malfunction. Data blocks to be accessed should be distributed over the disk medium equally.
(1) Unrecoverable error rate
Errors which cannot ...replaced by alternate block assignments are not considered.
(2) Mean Time To Repair (MTTR)
MTTR is the average time taken by a well-trained service mechanic to bad environmental conditions, power trouble, host system trouble...
Manual/User Guide - Page 84
...and dismounting drives.
5.1 Notes on Handling Drives The items listed in the specifications in Table 2.1 must be careful when unpacking. b) Be careful not to give the drive shocks or ... such as a rubber mat, not on hard material such as a desk. b) Do not leave the drive in the drive, note the following after installation and preparation for setting.
(2) Unpackaging a) Use a flat work area...
Manual/User Guide - Page 90
... power from the drive to Figures 5.2 and 5.3. Set the SCSI ID so that there are no duplicates between SCSI devices on LP/MP, refer to the SCSI terminal resistance power source (TERMPOW). However, this setting may not be used with SCA2 type 16 bit-SCSI (LC/MC). For information on the same SCSI bus.
2. Table 5.2 Setting SCSI terminal power supply...
Manual/User Guide - Page 99
... cable connection:
• All connectors including other SCSI devices are as follows. c) Check the setting of logical data blocks after initialization is formatted with a specific (default) data format for a recoverable error. Note that the checking procedure of cylinders in the format parameter (page code = 3) and drive parameter (page code = 4).
5 - 16
C141-E064-01EN
The user...
Manual/User Guide - Page 103
... operations.
(2) Disconnection/reconnection parameters (page code = 2)
The following performance factors of the system:
• Time required for reconnection processing • Average data transfer rate of the SCSI bus • Average amount of processing data specified with a command
Refer to evaluate the validity of SCSI Logical Interface Specifications for the parameter values to be...
Manual/User Guide - Page 111
...; Sense data • Other error analysis information
CAUTION
Data loss Save data stored on the disk drive before requesting repair. The DE cannot be replaced in the field. Generally, the following information must be replaced in the field.
(4) Service system and repairs
Fujitsu has the service system and repair facility for replacing or repairing the disk drive. Note:
The "average DE...
Manual/User Guide - Page 129
... unit 1-9 Mode setting 5-8 Mode settings 5-9 Model name 2-1, D-1, D-2 Motor start mode 5-8 Motor start mode setting 5-8 Mounting drives 5-10 Mounting frame...sync 3-8 EPR4ML 1-9 Packaging 5-2 Partial response class 4 maximum likelihood
1-9 Parts that can be replaced in the field 6-6 Physical sector allocation 3-6 Positioning error rate 2-5 Power cable 4-28 Power on/off sequence 4-13, 4-14 ...
Fujitsu MAF3364LC Reviews
We have not received any reviews for Fujitsu yet.