User's Guide (.htm)
Page 38
...RPS connector, console port, and power connector. RJ-45 ports designated as 1000Base-T ports • Console port - Ports G3- www.dell.com | support.dell.com There are all the device LEDs. The Stack ID button is marked with the following ports: • 48 FE ports - ...-X SFP ports • 2 Gigabit ports - Console Port RPS Connector Power Connector PowerConnect 3448 Port Description The PowerConnect 3448 device is used to select the unit number. Designated as stacking ports, or used to manually reset the device. The second button is the Reset Button which is configured with ...
...RPS connector, console port, and power connector. RJ-45 ports designated as 1000Base-T ports • Console port - Ports G3- www.dell.com | support.dell.com There are all the device LEDs. The Stack ID button is marked with the following ports: • 48 FE ports - ...-X SFP ports • 2 Gigabit ports - Console Port RPS Connector Power Connector PowerConnect 3448 Port Description The PowerConnect 3448 device is used to select the unit number. Designated as stacking ports, or used to manually reset the device. The second button is the Reset Button which is configured with ...
User's Guide (.htm)
Page 39
... are a Two-Wire Serial Interface (TWSI) for debugging, software download etc. The following figure illustrates the PowerConnect 3448 back panel: Figure 2-4. The Stack ID button is used to manually reset the device. The default baud rate is prevented. The baud rate can be configured from 2400 bps ...up to select the unit number. PowerConnect 3448 Back Panel Console Port RPS Connector Power Connector The back panel...
... are a Two-Wire Serial Interface (TWSI) for debugging, software download etc. The following figure illustrates the PowerConnect 3448 back panel: Figure 2-4. The Stack ID button is used to manually reset the device. The default baud rate is prevented. The baud rate can be configured from 2400 bps ...up to select the unit number. PowerConnect 3448 Back Panel Console Port RPS Connector Power Connector The back panel...
User's Guide (.htm)
Page 47
... third member is 3, and the fourth Stack member is either 1 or 2 depending on the front panel, for manual reset of 1 or 2. For example, if there are not reset. Ventilation System The PowerConnect 3424/P and PowerConnect 3448/P switches with the PoE feature have a reset button, located on the Unit ID of booting the device. The...
... third member is 3, and the fourth Stack member is either 1 or 2 depending on the front panel, for manual reset of 1 or 2. For example, if there are not reset. Ventilation System The PowerConnect 3424/P and PowerConnect 3448/P switches with the PoE feature have a reset button, located on the Unit ID of booting the device. The...
User's Guide (.htm)
Page 56
...configured LED number (corresponding to the previously saved unit ID) begins to 6 are for 15 seconds. www.dell.com | support.dell.com Figure 3-6. The default setting is manually configured by pressing the Stack ID button until the appropriate Stack ID LED is connected to a VT100 terminal... stack device has a unique identifying unit ID that the stand-alone/Master device Console port is illuminated. 56 Installing the PowerConnect 3424/P and PowerConnect 3448/P Unit ID Selection Process The unit ID selection process is as follows: 1 Ensure that defines the unit's position and function...
...configured LED number (corresponding to the previously saved unit ID) begins to 6 are for 15 seconds. www.dell.com | support.dell.com Figure 3-6. The default setting is manually configured by pressing the Stack ID button until the appropriate Stack ID LED is connected to a VT100 terminal... stack device has a unique identifying unit ID that the stand-alone/Master device Console port is illuminated. 56 Installing the PowerConnect 3424/P and PowerConnect 3448/P Unit ID Selection Process The unit ID selection process is as follows: 1 Ensure that defines the unit's position and function...
User's Guide (.htm)
Page 61
... is established and the console prompt is prompted to Dell Easy Setup Wizard The Setup Wizard guides you through the initial switch configuration, and gets you up and running as quickly as possible. Configuring PowerConnect 3424/P and 3448/P 61 You can skip the setup wizard, and ... configuration is displayed: Welcome to use the Setup Wizard. After the initial configuration, the device can skip the Setup Wizard, and manually configure the device through the device CLI mode. The Setup Wizard configures the following fields. • SNMP Community String and SNMP Management...
... is established and the console prompt is prompted to Dell Easy Setup Wizard The Setup Wizard guides you through the initial switch configuration, and gets you up and running as quickly as possible. Configuring PowerConnect 3424/P and 3448/P 61 You can skip the setup wizard, and ... configuration is displayed: Welcome to use the Setup Wizard. After the initial configuration, the device can skip the Setup Wizard, and manually configure the device through the device CLI mode. The Setup Wizard configures the following fields. • SNMP Community String and SNMP Management...
User's Guide (.htm)
Page 76
...automatic correction of speed, duplex mode and flow control on all switching 10/100/1000BaseT ports. www.dell.com | support.dell.com Port Default Settings The general information for configuring the device ports includes the short description of ... of the auto-negotiation mechanism and the default settings for hubs and switches is disabled. It can be manually set to prevent buffer overflow. By default, this feature is known as MDI (Media Dependent Interface), and...Pressure The device supports back pressure for additional traffic. 76 Configuring PowerConnect 3424/P and 3448/P
...automatic correction of speed, duplex mode and flow control on all switching 10/100/1000BaseT ports. www.dell.com | support.dell.com Port Default Settings The general information for configuring the device ports includes the short description of ... of the auto-negotiation mechanism and the default settings for hubs and switches is disabled. It can be manually set to prevent buffer overflow. By default, this feature is known as MDI (Media Dependent Interface), and...Pressure The device supports back pressure for additional traffic. 76 Configuring PowerConnect 3424/P and 3448/P