User Guide
Page 63
...the projected image according to input signal format with an Original setting. Troubleshooting Your Projector 63 To replace the lamp, see "Changing the Lamp" on . If the problem persists, contact Dell™. If the image is solid amber Possible Solution (continued) The projector automatically detects the input ...this occurs, the projector does not turn back on page 67. The display automatically shuts down . If the LAMP light is properly installed. If the LAMP light is solid blue, the color wheel has failed and the projector will automatically shut down . It will maintain...
...the projected image according to input signal format with an Original setting. Troubleshooting Your Projector 63 To replace the lamp, see "Changing the Lamp" on . If the problem persists, contact Dell™. If the image is solid amber Possible Solution (continued) The projector automatically detects the input ...this occurs, the projector does not turn back on page 67. The display automatically shuts down . If the LAMP light is properly installed. If the LAMP light is solid blue, the color wheel has failed and the projector will automatically shut down . It will maintain...
User Guide
Page 66
OFF AMBER Flashing OFF OFF OFF OFF OFF OFF AMBER OFF AMBER AMBER OFF OFF AMBER Flashing 66 Troubleshooting Your Projector If this problem persists, contact Dell. Unplug the power cord after three minutes and then turn on the projector. DC supply (+12V) Lamp module connection failed Lamp is properly installed. Power supply has been interrupted. Lamp module connection may be disrupted. Check the lamp module and ensure that it is defective. Lamp failure Fault - If the problem persists, contact Dell. The projector automatically shuts down. Replace the lamp.
OFF AMBER Flashing OFF OFF OFF OFF OFF OFF AMBER OFF AMBER AMBER OFF OFF AMBER Flashing 66 Troubleshooting Your Projector If this problem persists, contact Dell. Unplug the power cord after three minutes and then turn on the projector. DC supply (+12V) Lamp module connection failed Lamp is properly installed. Power supply has been interrupted. Lamp module connection may be disrupted. Check the lamp module and ensure that it is defective. Lamp failure Fault - If the problem persists, contact Dell. The projector automatically shuts down. Replace the lamp.
User Guide
Page 67
... this problem persists after replacing the lamp, contact Dell™. CAUTION: Do not touch the bulb or the lamp glass at least 30 minutes. 3 Loosen the two screws that secure the lamp cover, and remove the cover. 4 Loosen the two screws that secure the lamp. 8 Replace the lamp cover and tighten the ...two screws. For more information, see www.dell.com/hg. 1 Turn off the projector and disconnect the power cord...
... this problem persists after replacing the lamp, contact Dell™. CAUTION: Do not touch the bulb or the lamp glass at least 30 minutes. 3 Loosen the two screws that secure the lamp cover, and remove the cover. 4 Loosen the two screws that secure the lamp. 8 Replace the lamp cover and tighten the ...two screws. For more information, see www.dell.com/hg. 1 Turn off the projector and disconnect the power cord...
User Guide
Page 71
.... RJ45 port: One RJ45 connector for control of the rated lumens for any way. Philips 225 W user-replaceable lamp (up to 4000 hours in stressful conditions which may include dusty environments, under high temperatures, many hours per day and abrupt powering-off...any projector is a measure of a projector in eco mode) NOTE: The lamp life rating for the specified lamp. RS232 port: One mini-DIN 6-pin for remote support. Lamp life is not a specification for more than 50 percent of a lamp sample population to have brightness decrease by approximately 50 percent of projector through...
.... RJ45 port: One RJ45 connector for control of the rated lumens for any way. Philips 225 W user-replaceable lamp (up to 4000 hours in stressful conditions which may include dusty environments, under high temperatures, many hours per day and abrupt powering-off...any projector is a measure of a projector in eco mode) NOTE: The lamp life rating for the specified lamp. RS232 port: One mini-DIN 6-pin for remote support. Lamp life is not a specification for more than 50 percent of a lamp sample population to have brightness decrease by approximately 50 percent of projector through...