BenQ CP120C - XGA DLP Projector Support and Manuals
Popular BenQ CP120C Manual Pages
User Manual - Page 2
....
*DLP, Digital Micromirror Device and DMD are copyrights of their respective companies or organizations. No part of this publication and to make changes from time to time in any form or by BenQ Corporation. All rights reserved. Others are trademarks of BenQ Corporation.
Copyright
Copyright 2006 by any means, electronic, mechanical, magnetic, optical, chemical, manual or...
User Manual - Page 4
... the lens 37 Cleaning the projector case 37 Storing the projector 37 Transporting the projector 37 Calculation of lamp hour 38 Warning message 38 Replacing the lamp 39
Temperature information 40 Indicators 41
Troubleshooting 43
Specifications 45
Projector specifications 45 Dimensions 46 Timing chart 46
Supported timing for PC input 46 Supported timing for Component-YPbPr Input...
User Manual - Page 7
... straight at the projector
voltage between 100 to qualified service personnel.
• Always open the
•
cabinet.
Save this
user's manual for safety of information technology equipment. but could fail if power cuts or surges of this product, it is recommended that you follow the instructions mentioned in this user's manual before
projector lamp is on the product...
User Manual - Page 11
... conditions, and selected input source contrast/brightness settings.
• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. Introduction 5 This is normal and expected behavior.
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly design to reduce the power consumption...
User Manual - Page 12
...projector is shipped with Battery
User's Manual
User's Manual CD
USB Cable
VGA Cable
Power Cord
Optional accessories
• Macintosh adapter
• Combo (for notebook computer and
• 132W lamp module (replacement or
projector...of purchase. Quick Start Guide Remote Control with the cables required for your place of the items shown below.
Projector
Soft Carry Case
Pull ...
User Manual - Page 16
...best picture settings for more information.)
Turns on , press twice to switch the projector to "Using...
11 6
1. When the projector is in the lower
right corner of the screen.
Press Blank again to make adjustments. 5. When the projector is pressed. To release the... (on page 30 for more
information.) Manually corrects distorted images resulting from an angled projection...
User Manual - Page 18
...installed in the Advance > Mirror menu after you should consider its intended use and input signal aspect ratios. To be able to project a complete 16:9 (widescreen) aspect ratio image, the projector... setting, and the video format each factors in front of your projector Positioning your projector
Choosing a location
Your projector is designed to position the projector for quick setup ...
User Manual - Page 19
... left
columns labelled '4:3 Screen Diagonal' and '4:3 Aspect in mm'.
The modern digital projector does not project directly forward (like flat on a table), and positioned directly perpendicular (...projections (or projecting onto angled surfaces).
BenQ has provided a table of 4:3-aspect-ratio screen sizes (see from the horizontal plane of the projector for keystone correction. Refer to the...
User Manual - Page 27
... time as set by the Auto Off function.
The POWER indicator light flashes green and stays green when the unit is projected. The start up procedure takes about the password function, refer..., it could become deformed due to select the four password digits, then press the AUTO button. Using the projector 21 Using the projector
Start up , a default BenQ logo is on. Switch all of a dialog on ...
User Manual - Page 28
...for the first time,
Password Setup
a prompt will see the message "Out of the password. Use the3Left or4Right button to cancel the password set through the on -screen
menu. Password Keep this manual, and keep the manual in a safe place.
4.
To set a password
CAUTION: Once a password has been set -up is available to confirm.
The set , the projector cannot be asked to select...
User Manual - Page 29
... incorrect, a "Password Error" message displays. To adjust the projector:
1.
The strong light from the local BenQ service center to fine tune the horizontal angle. To retract the foot, hold the4Right button for 5 seconds.
If the screen and the projector are an authorized user of Keystone in the Picture menu, on the projector control panel, or on to verify...
User Manual - Page 39
... it in a safe place for the first time, you activate the password functionality and subsequently forget the password. If viewing online, print out this manual and write the password you used in this function is selected, the projector is password-protected.
The following settings will be inconvenienced if you have to a new one. The range is activated for...
User Manual - Page 46
Ensure the handle is not replaced as this could cause damage. Step 9. Resetting the lamp counter
Do not reset if the lamp is fully laid flat and locked in...distortion of the following possible problems: • The internal temperature is removed. Turn the projector off and contact qualified service personnel for 5 seconds to display the total used lamp time. For more detailed ...
User Manual - Page 55
...73/23/EEC).
EEC statement
Here by, BenQ Corporation, declares that interference will not occur in a particular installation.
Connect the equipment into an outlet on... (Canada)
This Class B digital apparatus complies with the essential requirements set out in the Council Directive on , the user is encouraged to try to...instructions, may cause harmful interference to radio communications.
BenQ CP120C Reviews
Do you have an experience with the BenQ CP120C that you would like to share?
Earn 750 points for your review!
We have not received any reviews for BenQ yet.
Earn 750 points for your review!