BenQ PW9620 DLP Projector Support and Manuals
Get Help and Manuals for this BenQ item
View All Support Options Below
Free BenQ PW9620 DLP Projector manuals!
Problems with BenQ PW9620 DLP Projector?
Ask a Question
Free BenQ PW9620 DLP Projector manuals!
Problems with BenQ PW9620 DLP Projector?
Ask a Question
Popular BenQ PW9620 DLP Projector Manual Pages
User Manual - Page 3
... 54 Replacing the filter...55 Specifications...56 Dimension...57 Timing chart...58 PC timing...58 3D supported timing...59 RS232 command control 61 Control the projector through a network 64 Set up the projector for networking 64 Control the projector through a web browser 65 Projector Status...65 Alert mail setup...66 Crestron control page...67 Troubleshooting...69 Indicator...
User Manual - Page 11
Downloaded From projector-manual.com BenQ Manuals
11 Press MENU key to exit to projection image.
• LENS SHIFT Press to move lens move up, down, left and right.
• ENTER Press to select or accept settings.
• MENU Press to hide or display OSD menu.
• EXIT Press to go back to last menu or...
User Manual - Page 16
... common way to position the projector for more information. Note:
• Ceiling installation must be used at
temperatures between the projector and the rest of your dealer for quick setup and portability.
3. Note that a special rear projection screen and the BenQ Projector Ceiling Mount Kit are covered Downloaded From projector-manual.com BenQ Manuals
16 Front Ceiling: Select this...
User Manual - Page 37
English
Main menu CONTROL
SERVICE
RS232 Startup Logo Trigger
Auto Search Dynamic Black 3D
Model Serial Number Software Version Active Source Pixel Clock Signal Format H/V Refresh Rate Lamp 1 Time Lamp 2 Time Blue Only Factory...Language
English, Deutsch, Español, Français,
Italiano, Svenska, Português,
On Off OK Cancel
Downloaded From projector-manual.com BenQ Manuals
37
User Manual - Page 47
...speed). Subnet: Set up IP address of gateway. Caution:
• If the projector is set to standby at...settings till the following communication channel before using the remote control function.
47 That is, the IP address is shown on network control connections and settings, please refer to the Remote control manual. • RS232 Baud Rate: Set transmission speed to On or Off. Gateway: Set...
User Manual - Page 49
...projector supports DLP Link and 3D IR sync. SERVICE
DISPLAY
MPxx-0Dxx-PUxx-RDxx-SExx-PDxx-xxxx VGA 1024x768 @60Hz H: 49.578 KHZ V: 60HZ
<
Off
>>
Display basic information on the projector.
• Model Projector model number
• Serial Number Projector...fatigue or a lack of software installed in the projector.
• Active Source Display ...projector-manual.com BenQ Manuals
49
User Manual - Page 56
...Specifications
Model
Display Device
Resolution
HDMI (Compatible with HDCP)
DVI-D (Compatible with HDCP)
Input Terminals
Display Port (Compatible with HDCP)
Computer-2 (5BNC)
Computer-1 (D-sub 15p)
Monitor Out (D-sub 15 p)
Output Terminals
Trigger (φ3.5mm stereo min jack)
3D IR Sync (VESA mini din)
Lan (RJ-45)
Control and Service...USB (Type B) for service
1
Power Requirement
AC...
User Manual - Page 63
... Miscellaneous Write Read Write Read
Model Name Blank On Blank Off ...3D Side by side 3D inverter disable 3D inverter 3D Sync Status Remote Set Remote Set Status
*modelname=?# *blank=on# *blank=off# *blank=?# *freeze=...
High Altitude mode status
*Highaltitude=?#
Read Write
Error Code Lens Shift Up
*error=report# *lst=up#
Write
Lens Shift Down...projector-manual.com BenQ Manuals
*keyst=?#
63
User Manual - Page 64
... IP address, and 0. 0. 0. 0 is set DHCP option to Off and select Apply to activate it.The DHCP service assigns an IP address and settings.The IP address, Subnet and Gateway options will assign an IP address to increase or decrease the number in network setting until the following message disappears. Downloaded From projector-manual.com BenQ Manuals
64
User Manual - Page 65
... projector settings.
Crestron: Crestron compatible network browser control page PJLink: This page lets you set up a security password for projector abnormality email reminders. In case of network control software : Current IP address : Current subnet setting : Current gateway setting : Current DNS server setting : Preset MAC address
Downloaded From projector-manual.com BenQ Manuals
65...
User Manual - Page 66
... email through SMTP server. : Set up user password. : Enable or disable E-mail Alert function. : Set up sender's email address. : Set up recipient's email address. : Set up CC recipient's email address. : Set up projector name or ID : Set up installation location of a projector error. The reminder email is completed. Downloaded From projector-manual.com BenQ Manuals
66 Make the following...
User Manual - Page 68
...with Creston compatible devices. Control your projector with PJLink commands PJLink is masked. Password: Set up security password at length of signal sources. Press again to control projectors with standard commands regardless of who made it. Blank: Pause the image projection, i.e. See relevant manuals for detailed setup steps. A projector featuring PJLink functions can be controlled...
User Manual - Page 69
... the Power key on top cover of problems with setup or system error.The LEDs on the control panel. If the problem persists, call the local service center. Shutter LED
LED display Close Flashing
Green
Projector status Shutter opened Shutter closed
Operation tips
Downloaded From projector-manual.com BenQ Manuals
69 Call the local service center. Lamp life expires
Call the...
User Manual - Page 70
... Setting menu of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on the remote control or projector. 4. Use the Keystone button on the screen 1. To ensure the problem is blurred 1. Image problems
Problem: No image appears on the remote control to correct the problem.
Downloaded From projector-manual.com BenQ...
User Manual - Page 71
.... 6.
Ensure that the remote control code conforms to turn off .
Check that the Power LED is green. 4. If you have the projector serviced. Check the battery polarity. 5. Downloaded From projector-manual.com BenQ Manuals
71 Replace the lamp module. 10.Put the old lamp back in the projector and have the projector serviced. Adjust the Brightness setting on back of the OSD...
BenQ PW9620 DLP Projector Reviews
We have not received any reviews for BenQ yet.