Dimension Guide
Page 1
... for installation of gas that can be located in the system. This valve should be in insufficient gas supply. Model/serial rating plate (located on the types of rigid gas pipe. Cabinet opening and closing. Grounded outlet I . For complete details, see NOTE*....) *Range can be equipped with a manual shutoff valve. 30" (76.2 cm) Freestanding Gas Range PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS AGR5844VD AGR6011VD Gas supply: This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for planning purposes only....
... for installation of gas that can be located in the system. This valve should be in insufficient gas supply. Model/serial rating plate (located on the types of rigid gas pipe. Cabinet opening and closing. Grounded outlet I . For complete details, see NOTE*....) *Range can be equipped with a manual shutoff valve. 30" (76.2 cm) Freestanding Gas Range PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS AGR5844VD AGR6011VD Gas supply: This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for planning purposes only....
Installation Instruction
Page 4
...check with installation clearances specified on the oven frame behind the top left side of this range is located on the model/serial rating plate. Thickness of combustion and ventilation air. ■ It is to the floor during transit. To install the antitip bracket... nut driver ■ Quadrex®† or Phillips screwdriver ■ Masking tape Parts supplied Check that the materials used . The model/serial rating plate is installed in accordance with the requirements of NLW Holdings, Inc. 4 See "Electrical Requirements" section. ■ Proper gas supply connection ...
...check with installation clearances specified on the oven frame behind the top left side of this range is located on the model/serial rating plate. Thickness of combustion and ventilation air. ■ It is to the floor during transit. To install the antitip bracket... nut driver ■ Quadrex®† or Phillips screwdriver ■ Masking tape Parts supplied Check that the materials used . The model/serial rating plate is installed in accordance with the requirements of NLW Holdings, Inc. 4 See "Electrical Requirements" section. ■ Proper gas supply connection ...
Installation Instruction
Page 5
Model/serial rating plate (located on the oven frame behind the top left side of the oven door) *Range can be raised approximately 1" (2.5 cm) by not less than ...
Model/serial rating plate (located on the oven frame behind the top left side of the oven door) *Range can be raised approximately 1" (2.5 cm) by not less than ...
Installation Instruction
Page 6
...This gas range is required. If the metal chassis of the above code standards can be obtained from the gas specified on the model/serial rating plate for use with American National Standard, National Fuel Gas Code ANSI Z223.1 - Install a shut-off valve. Observe all gas connections. ...latest edition. The model/serial rating plate located on the oven frame behind the top left side of the oven door has information on a GFCI-protected circuit. Gas Supply Line ...
...This gas range is required. If the metal chassis of the above code standards can be obtained from the gas specified on the model/serial rating plate for use with American National Standard, National Fuel Gas Code ANSI Z223.1 - Install a shut-off valve. Observe all gas connections. ...latest edition. The model/serial rating plate located on the oven frame behind the top left side of the oven door has information on a GFCI-protected circuit. Gas Supply Line ...
Installation Instruction
Page 7
...: The rigid pipe connection requires a combination of pipe fittings to obtain an in excess of 4% for each 1,000 ft (304.8 m) above 2,000 ft (609.6 m), ratings are not sure about the inlet pressure. B A C A. The rigid pipe must be used for connecting range to the gas supply line. ■ A ½" ...(1.3 cm) male pipe thread is for turning on the model/serial rating plate are for testing regulator must be equipped with the range connection. Line pressure testing above the manifold pressure shown on the model/serial...
...: The rigid pipe connection requires a combination of pipe fittings to obtain an in excess of 4% for each 1,000 ft (304.8 m) above 2,000 ft (609.6 m), ratings are not sure about the inlet pressure. B A C A. The rigid pipe must be used for connecting range to the gas supply line. ■ A ½" ...(1.3 cm) male pipe thread is for turning on the model/serial rating plate are for testing regulator must be equipped with the range connection. Line pressure testing above the manifold pressure shown on the model/serial...
Installation Instruction
Page 15
Burner base 3. Set gas orifice spud aside. C A D LP Gas Orifice Spud Chart for Surface Burners Burner Rating Color Size ID Number 14,000 BTU 11,000 BTU 8,000 BTU 5,000 BTU Yellow/Orange Yellow/Brown Yellow/Black Yellow/White 1.07 mm 0.99 ...
Burner base 3. Set gas orifice spud aside. C A D LP Gas Orifice Spud Chart for Surface Burners Burner Rating Color Size ID Number 14,000 BTU 11,000 BTU 8,000 BTU 5,000 BTU Yellow/Orange Yellow/Brown Yellow/Black Yellow/White 1.07 mm 0.99 ...
Installation Instruction
Page 17
.... 7. Remove oven racks. 2. Orifice spud B. Remove burner cap. 2. Igniter electrode B. C A D B Refer to the following chart for the remaining burners. Natural Gas Orifice Spud Chart Burner Rating Color Size ID Number 17,000 BTU 15,500 BTU 14,200 BTU 13,000/13,500 BTU 12,000/12,500 BTU 9,500 BTU...
.... 7. Remove oven racks. 2. Orifice spud B. Remove burner cap. 2. Igniter electrode B. C A D B Refer to the following chart for the remaining burners. Natural Gas Orifice Spud Chart Burner Rating Color Size ID Number 17,000 BTU 15,500 BTU 14,200 BTU 13,000/13,500 BTU 12,000/12,500 BTU 9,500 BTU...