Fluke 116 Support Question
Fluke 116 Support Question
Find answers below for this question about Fluke 116.Need a Fluke 116 manual? We have 2 online manuals for this item!
Question posted by unklare on November 19th, 2021
How To Zero Ohm Out
when in ohm scale and touch end of leads together not getting zero . Have tried different leads but not helping. Is there a way to adjust for loss in lead
Current Answers
Answer #1: Posted by SonuKumar on November 21st, 2021 9:20 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,620,300
Member since:
May 9th, 2021 Points: 16,620,300
Why does my multimeter not go to zero in the ac volts mode?
Q: Why does my multimeter not go to zero in the ac volts mode? ... Most of these true-rms type multimeters have a minimum ac voltage and current level specification for both the ac volts and ac current modes, typically specified from 3% to 5% of range.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Fluke 116 Manual Pages
Fluke 116 Digital Multimeter Datasheet - Page 1
... to quickly troubleshoot problems with HVAC equipment and flame sensors. Fluke 116
HVAC Multimeter
with Temperature and Microamps
Technical Data
Actual size
R
N10140
Compact true-rms meter for ...HVAC troubleshooting
The Fluke 116 was specifically designed for HVAC applications • Microamps to test flame sensors • LoZ: helps prevent false readings due to ghost...
Fluke 116 Digital Multimeter Datasheet - Page 2
...zero readings when the test leads...Ω
0.1 mV
0.001 V 0.01 V 0.1 V 1 Ω
Ohms
Diode test Capacitance
Lo-Z capacitance Temperature2 (Type-K thermocouple)
600.0 Ω ... + 20 10 % + 2 typical 1 % + 102 1 % + 182
Ordering information
Fluke-116
HVAC Multimeter with Temperature and Microamps
Fluke. Auto-V LoZ, and ac mV are shorted together. AC ...scale. For volts, crest factor of range.
Fluke 116 Users Manual - Page 1
All rights reserved. ®
116
True-rms Multimeter
Users Manual
PN 2538688 July 2006, Rev. 1, 2/07
© 2006, 2007 Fluke Corporation. Printed in China All product names are trademarks of their respective companies.
Fluke 116 Users Manual - Page 2
..., misuse, alteration, contamination, or abnormal conditions of operation or handling.
Fluke Europe B.V. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.
Fluke 116 Users Manual - Page 3
... IEC 61010-1 2nd Edition standards. Unsafe Voltage To alert you to the presence of danger from transient impulses.
True-rms Multimeter
Introduction
The Fluke Model 116, is a battery-powered, true-rms multimeter (hereafter "the Meter") with a 6000-count display and a bar graph.
Fluke 116 Users Manual - Page 4
... • Do not use the Meter around explosive gas or vapor. • When using test leads or probes, keep your fingers behind the finger guards. • Only use proper terminals, switch ...Use caution with voltages above 30 V ac rms, 42 V ac peak, or 60 V dc. 116 Users Manual
Safety Information A "XWWarning" statement identifies hazardous conditions and actions that could cause bodily harm or...
Fluke 116 Users Manual - Page 5
Refer to measure voltages in hazardous areas. • Avoid working
in circuits that could be impaired. • Check the test leads for disposal.
3
Symbols
B AC (Alternating Current)
N Battery (Low battery when shown on display.)
F DC (Direct Current)
T Double Insulated
X Hazardous voltage
W Important Information; True-rms Multimeter ...
Fluke 116 Users Manual - Page 6
... Diode Test
C
O
Input is set to Continuity.
Symbol
Meaning
A
s
The Meter function is a negative value. Measured input voltage ≥ 30 V, or voltage overload condition (OL). 116 Users Manual
Display
5 4 3 2 1
14 13
6 12 15
7
9
8
10
11 16
eeo02f.eps
No.
Fluke 116 Users Manual - Page 8
... must be repaired before it will operate. Description
A Common (return) terminal for measuring voltage, continuity, resistance, capacitance, frequency, temperature, microamps and testing diodes..
Internal error.
116 Users Manual
Terminals
COM
+
2
1
edy01f.eps
No. The Meter must be repaired before it will operate.
6
Fluke 116 Users Manual - Page 9
... °C to 400 °C (-40 °F to 600 V.
y
Temperature from 0.001 V to 752 °F) with a low impedance input. DC voltage from 0.1 to 600 mV.
Ω
Ohms from 6.0 to 40 MΩ. DC-coupled. Note: All ac functions and Auto-V LoZ are dc coupled.
7 Auto-V LoZ, AC mV and AC μA are true...
Fluke 116 Users Manual - Page 10
...and select the range yourself. The backlight
automatically turns off . Pressing any button or turning the rotary switch awakens the Meter.
116 Users Manual
Battery Saver ("Sleep Mode") The Meter automatically enters "Sleep mode" and blanks the display if there is displayed.)
...Meter selects the range with the best resolution.
• In the Manual Range mode, you apply a different voltage.
Fluke 116 Users Manual - Page 11
...Power-Up Options
f p q g
Q
Turns on . When connecting the test leads to the circuit or device, connect the common (COM) test lead before connecting the live lead before removing the common test lead.
9 If you press qwhile in the following pages show how to Autorange and... the following table while turning the Meter on all display segments. when removing the test leads, remove the live...
Fluke 116 Users Manual - Page 12
116 Users Manual
Measuring Resistance
Testing for Continuity
XWWarning
eeo04f.eps
To avoid electric shock, injury, or damage to the Meter, disconnect circuit power and discharge ...
Fluke 116 Users Manual - Page 14
Connect the Meter between the flame sensor probe and the control module.
3. 116 Users Manual
Measuring AC and DC Current WWarning
To avoid personal injury or damage to the Meter:
• Never attempt to make an in-circuit ...
Fluke 116 Users Manual - Page 16
... bar graph and range annunciator indicate the AC voltage present.
3. If the frequency of times the signal crosses a trigger level each second.
edy09f.eps
14 116 Users Manual
Measuring Frequency XWWarning
To avoid electrical shock, disregard the bar graph for a stable reading.
Fluke 116 Users Manual - Page 18
In the 60 V range, for making peak and null adjustments. Replacing the Battery
aej11f.eps
16
eeo11f.eps Because the bar graph updates much ...example (see below), the major divisions on the negative sign and the segments up to the full-scale value of the selected range. 116 Users Manual
Using the Bargraph The bar graph is disabled when measuring capacitance and temperature.
The number of...
Fluke 116 Users Manual - Page 20
... Battery Life Alkaline: 400 hours typical, without backlight Safety Compliances Complies with relative humidity at www.Fluke.com. Extended specifications are available at 0 % to 90 %. 116 Users Manual
General Specifications Accuracy is specified for 1 year after calibration, at operating temperatures of 18 °C to 28 °C, with ANSI/ISA 82.02...
Fluke 116 Users Manual - Page 22
116 Users Manual
Function Continuity
Ohms
Diode test Capacitance Lo-Z Capacitance Temperature (Type K Thermocouple)
Table 1 Accuracy Specifications (cont.)
Range
600 Ω
600.0 Ω 6.000 kΩ 60.00 kΩ 600.0 kΩ 6.000 M&#...
Fluke 116 Users Manual - Page 23
... probe.
[3] Frequency is normal for this and other true-rms meters to display nonzero readings when the test leads are disconnected from a circuit or are specified from 1 % to 100% of ≤3 at full scale. Auto-V LoZ, AC mV, and AC μA are dc-coupled.
[2] Temperature uncertainty (accuracy) does not include the error...
Fluke 116 Users Manual - Page 24
116 Users Manual
Function Volts AC Volts DC Auto-V LoZ
Ohms Diode Test
Table 2. Input Characteristics
Input Impedance (Nominal)
>5 MΩ 10 MΩ 60 dB at dc, 50 or 60 Hz >100 dB at dc, 50 or 60 Hz
~3 kΩ 60 dB at dc, 50 or 60 Hz
Open Circuit Test Voltage
Similar Questions
My Meter Does Not Read Ac Milliamps But It Reads Amps, What Is The Problem?
(Posted by bounnakkhaikhamext 2 years ago)
Burned Component
My 117 has a burned component and now it will no longer measure voltage, either AC or DC. I think th...
My 117 has a burned component and now it will no longer measure voltage, either AC or DC. I think th...
(Posted by aviator3583 4 years ago)
