Fluke 8808A Support and Manuals
Get Help and Manuals for this Fluke item
Most Recent Fluke 8808A Questions
My Meter Does Not Read Ac Milliamps But It Reads Amps, What Is The Problem?
(Posted by bounnakkhaikhamext 2 years ago)
Popular Fluke 8808A Manual Pages
Fluke 8808A Digital Multimeter Datasheet - Page 2
8808A Specifications
Voltage
100V Setting 90 V to 110 V 120V Setting 108 V to 132 V 220V Setting 198 V to 242 V 240V Setting 216 V to 264 V Frequency 47 Hz to full uncertainty specifications
Relative Humidity (non-condensing) Operating Uncontrolled (< 10°C) Power Consumption 15 VA peak (10 W average)
Dimensions
Height 88 mm (3.46 in) Width 217 mm (8.56 ...
User Manual - Page 4
... Settings of Power-Up Configuration 3-25 Calibration ...3-26
4
Operating the Meter Using the Computer Interface 4-1
ii 8808A
Users Manual
Storing and Shipping the Meter 2-3 Power Considerations 2-3
Selecting the Line Voltage 2-4 Replacing the Fuses 2-4
Line-Power Fuse 2-4 Current-Input Fuses 2-5 Connecting to Line Power 2-7 Turning Power On 2-8 Adjusting the Bail 2-8 Installing...
User Manual - Page 13
...; Closed-case calibration (no internal calibration adjustments)
Manual Set
The manual set for this Meter consists of 2.5, 20 and 100 samples/second (slow, medium and fast,
respectively) • Front-panel setup key for single key access to saved setups • A compare mode to determine if a measurement is a 5-1/2 digit dual-display multimeter designed for bench-top, field service, and system...
User Manual - Page 14
8808A
Users Manual
About this manual that relate to specific measurement functions. Chapter 5, "Operating the Meter using the Meter from the front panel. A Caution statement identifies conditions or practices that may appear on using the Meter to use or service the Meter.
In addition, follow all the information a new user will need to set up, configure, and...
User Manual - Page 16
... discharge can damage parts. Measurement Category II is for measurements not directly connected to the low voltage installation. See manual. Symbol
P J E G
I
Y
U <
~
CAT I is for disposal. Measurement Category I
Description
Standby power ON / OFF
Earth ground Capacitance Diode
Fuse
Digital signal Maintenance or Service Recycle Do not dispose of danger. Hazardous voltage.
Contact Fluke or...
User Manual - Page 17
... 8845A & 8846A Single Rack Mount Kit 8845A & 8846A Dual RS-232 Cable (2 m) Precision Electronic Prob Set 2X4 Wire Ohms 1000 V Test Lead FlukeView Forms Basic Software FlukeView Forms Software Upgrade to enhanced version
1 Introduction and Specifications Options and Accessories
Model / Part Number TL71 163030 166488 803293 943121 Y8846S Y8846D RS43 TL910 TL2X4W-PTII FVF-SC5 FVF-UG...
User Manual - Page 18
8808A
Users Manual
General Specifications
Voltage
100V Setting 90 V to 110 V 120V Setting 108 V to 132 V 220V Setting 198 V to 242 V 240V Setting 216 V to 264 V Frequency 47 Hz to 440 Hz Power Consumption 15 VA peak (10 ...;C to 50 °C Storage 40 °C to 70 °C Warm Up hour to full uncertainty specifications
Relative Humidity (non-condensing) Operating Uncontrolled (< 10°C)
User Manual - Page 20
For inputs from 1 % to 5 % of range. 8808A
Users Manual
AC Voltage Specifications
AC Voltage specifications are for ac sinewave signals >5 % of range and
User Manual - Page 31
... to Table 2-2 for line-power cord types available from Fluke. 2 Preparing the Meter for the line voltage is set to the correct setting.
2. Verify that the line voltage is installed.
3.
LC-1
LC-2
LC-3
LC-4
LC-5
LC-6
LC-7
Figure 2-3. Line-Power Cord Types Available from Fluke
Voltage / Current
Fluke Model Number
120 V / 15 A 240 V / 15 A 220 V / 16 A 240...
User Manual - Page 46
8808A
Users Manual
4-Wire Resistance Measurement The Meter incorporates two methods of the meter. To perform a 4-wire resistance measurement using Fluke's 2X4 test leads: 1. If required, press O to the Meter's input connectors as shown in Figure 3-6. 2. The function and measurement are displayed.
2W/4W
HI
INPUT V
...
User Manual - Page 62
8808A
Users Manual
Compare Commands and Queries 4-24 Trigger Configuration Commands 4-24 Miscellaneous Commands and Queries 4-25 RS-232 Remote / Local Configurations 4-25 RS-232 Save / Recall System Configurations 4-26 Sample Program Using the RS-232 Computer Interface 4-27
4-2
User Manual - Page 64
8808A
Users Manual
6. Press R to OFF. Refer to the "Setting Communication Parameters (RS-232)" section earlier in Table 4-2.
Press P ... displays. While the Meter will respond to remote commands during print-only operations, Fluke recommends first setting the Meter's echo mode to review the settings. The print rate is now configured for RS-232 printonly operations.
The Meter ...
User Manual - Page 66
... was successfully parsed and executed.
Installation Test for RS-232 Operation This procedure confirms that the Meter sends the following prompts: => No errors detected. Type *IDN? and Dn.n is the display's software version.
4-6 Verify that the Meter is properly set correctly. 3. Command was understood, but not executed. 8808A
Users Manual
Character Echoing and Deletion When the...
User Manual - Page 75
... enabled bit in angle brackets (for example, ).
4-15 4 Operating the Meter Using the Computer Interface Computer Interface Command Set
Table 4-7.
Request Service (RQS) is set to 1 if service requested from front panel or MSS is set to 1. Reading the Status Byte Register
The host reads the STB by related function and are listed in the...
User Manual - Page 76
... versions of the Event Status Register and then clears it.
8808A
Users Manual
Common Commands Table 4-8 describes common commands.
These fields are: Manufacturer (FLUKE); Event Status Enable Query
Meter returns the of the Meter as set by commas. Identification Query
Meter returns the identification code of the Event Status Enable Register as four fields separated...
Fluke 8808A Reviews
We have not received any reviews for Fluke yet.