Craftsman 21514 Support Question
Craftsman 21514 Support Question
Find answers below for this question about Craftsman 21514 - Belt & Disc Sander.Need a Craftsman 21514 manual? We have 1 online manual for this item!
Question posted by rmuskat on May 8th, 2011
Belt Change
How do I change the belt on my sander?
Model 531.215140
Thanks
Current Answers
Related Craftsman 21514 Manual Pages
Operation Manual - Page 1
Sears, Roebuck and Co., Hoffman
www.sears.com/craftsman
30657.00 Draft (04/07/09)
Estates, IL 60179 U.S.A.
Operator's Manual
CRRFISMRN °
4 x 36" Belt 6" Disc
SANDER Model No.
351.215141
CAUTION: Read and follow
all Safety Rules and Operating Instructions before First Use
of this manual with tool. Keep this Product.
Operation Manual - Page 2
... checking to these exposures vary, depending on how often you do not leave tool until it was not designed.
• Disconnect tool when changing belt or abrasive disc. • Avoid accidental start-up. Serious injury could occur if tool is
tipped or if belt or disc are unintentionally contacted. • Know your exposure to see that may cause...
Operation Manual - Page 3
... this manual to order replacement parts.
Check for completeness.
Insert Mounting Brackets into workpiece. (Motor force keeps it is a combination of the abrasive disc.
3 TOOLS NEEDED While assembling or adjusting your belt and disc sander, you have to stand in a place with ample lighting and correct power supply. • Turn machine off if it jams...
Operation Manual - Page 4
...at 0°. POWER SOURCE
WARNING: Do not connect sander to Figures 5 and 6. Heavy loads require that ...to prevent unauthorized use the table with both the disc and belt.
Normal loads will be plugged directly into a ...disc guard. ° Using a combination square, set the table perpendicular to
the disc, and secure in doubt as to whether the tool is properly grounded.
• This tool...
Operation Manual - Page 5
... not fit in outlet, have proper outlet installed by a qualified electrician.
° Inspect tool cords periodically, and if damaged, have repaired by local and national codes and ordinances.
(A... and cast iron providing stability and vibration-free operation. DESCRIPTION
The Craftsman Belt and Disc Sander is inspected.
EXTENSION CORDS
• The use a 3-prong to a live terminal.
&#...
Operation Manual - Page 6
... nut as needed to center belt on , always allow belt and disc to horizontal position, or any angle in severe eye damage. Abrasive belt must be adjusted from vertical to...become loaded (glazed) or frayed.
Adjusting Belt Tracking
° Quickly turn the sander OFF, push the switch to full speed before commencing power tool operation. Sanding belt assembly can be tightened securely.
°...
Operation Manual - Page 7
... while sanding. • Use a combination square to adjust miter gauge square to
belt (disc).
Keep end butted against table and move work evenly across down side (left) of abrasive disc. Position table on flat portion of sander.
ABRASIVE DISC SANDING
• Abrasive disc sanding is well suited for both horizontal and vertical positions. keep fingers away...
Operation Manual - Page 8
... available (See Recommended
Accessories, page 13). • Push tension lever towards drive drum to Replace Disc
WARNING: Make certain that the splice in this tool are permanently lubricated at your nearest Sears store.
8
Slide old belt off the drive and idler drums. NOTE: There may create a hazard unless repair is available at the...
Operation Manual - Page 9
...for proper voltage 2. Inspect all lead connections on pressure
See operation "Adjusting Belt Tracking"
9 Check power line for damaged insulation and
shorted wires 2. Replace capacitor 1. ...Inspect connections in power line
Motor fails to workpiece
Abrasive belt runs off top Not tracking properly wheel
CORRECTIVE ACTION 1. Install correct fuses or ...
Operation Manual - Page 10
Replacement Parts Illustration for Belt Housing
11
,..b
o
35 34
37 36
20 16
\ 39 Model 351.2151 41
Figure 17 -
Operation Manual - Page 11
...Pan Head Screw*
Back Stop 6mm Flat Washer* 6mm Lock Washer* 6-1.0x15mm Socket Head Bolt Drive Drum 8-1.25 x 10mm Set Screw Abrasive belt
Ball Bearing 6000ZZ* Bearing Plate Idler Assembly Spring Tension Lever 6-1.0 x 20mm Socket Head Bolt* Stud
QTY. 1 2 1 1 1 ...Cover 5-0.8 x 15mm Socket Head Bolt 5-0.8 x 8mm Flat Head Bolt Belt Cover Base Plate Drive Shaft Base Cover
Horizontal Stop 8-1.0mm Hex Nut*...
Operation Manual - Page 12
Replacement Parts Illustration for Motor and Disc
8
,,,,,.L
1
44 Model 351.21 5141
Figure 18 -
Operation Manual - Page 13
...7x 10ramPanHeadBolt*
4 39 STD8510044mmFlatWasher*
1 4O N/A
BottomPlate
6 41 23676.00 V-Belt
2 42 23677.00 MotoPr ulley 2 43 23678.00 Nut
8 44 23679....1 A 30657.00 OperatorM'sanual 1
Recommended Accessories A Abrasive Belts 4 x 36" (Fine) 120 Grit A Abrasive Belts 4 x 36" (Medium) 80 Grit A Abrasive Belt 4 x 36" (Coarse) 50 Grit A Abrasive Disc 6" Assorted Grit A Abrasive Cleaner
QTY. 2 4 1 ...
Similar Questions
Or91721 Replacement Belt
What is a replacement belt that can purchased with out a month relay from order from Sears Parts?
What is a replacement belt that can purchased with out a month relay from order from Sears Parts?
(Posted by Spauldid51 10 years ago)
How Much Did This Cost New
(Posted by Anonymous-54214 12 years ago)
Parts
Where can I buy a second table for the 21524 belt/disk sander. Part number 23655.00 Dan Mazel Bill...
Where can I buy a second table for the 21524 belt/disk sander. Part number 23655.00 Dan Mazel Bill...
(Posted by ss90680 12 years ago)
Belt Only Contacts Surface To Be Sanded Along One Edge.
My sander is brand-new (out lof the box). The belt installation was a piece of cake and adjusting th...
My sander is brand-new (out lof the box). The belt installation was a piece of cake and adjusting th...
(Posted by scorpio1155 12 years ago)